Hot Rolling Process Regime And Heating Temperature For Grain-Oriented Silicon Steel

Oct 20, 2025

Leave a message

Grain-Oriented Silicon Steel

 

For CGO steel (Conventional Grain-Oriented Steel) with MnS as the inhibitor and Hi-B steel (High Magnetic Flux Density Grain-Oriented Steel) with MnS + AlN as inhibitors, continuous casting slabs must undergo high-temperature heating. This heating process aims to dissolve the coarse MnS particles (>1 μm) in the slabs-these particles are mainly distributed in the equiaxed grain center region along the slab thickness direction. During hot rolling, fine and dispersed MnS particles (≤50 nm, equivalent to 10–1000 angstroms) are then precipitated. Therefore, the quality of heating directly affects the magnetic properties of the material in subsequent processes.

Hot Rolling Process Regime And Heating Temperature For Grain-Oriented Silicon Steel

 

Slab Heating Temperature

 

The required heating temperature for steel slabs is 1360–1380°C. Under equilibrium conditions, the dissolution temperature of MnS is 1320°C.

Since Hi-B steel has higher contents of Mn and C than Q steel, its slab heating temperature requirement is higher, ranging from 1380–1400°C.

 

The temperature of the slab must be uniform across all parts. This avoids magnetic property fluctuations and the occurrence of "black spots" caused by uneven temperature between the upper and lower parts of the slab.

 

 

Rough Rolling

 

Fine MnS particles precipitate during the finish rolling process. Therefore, it is essential to control three key parameters after rough rolling and before entering the finish rolling mill: the temperature, holding time, and thickness of the thin slab.

 

MnS starts to precipitate at approximately 1200°C, and the precipitation rate is the fastest at 1100–1150°C (the temperature range where the amount of γ-phase is the highest). Precipitation basically stops below 950°C.

 

To ensure the thin slab maintains a sufficiently high temperature, rough rolling adopts high-speed rolling with a large reduction ratio. The temperature is controlled using the "RT4min" standard in the hot rolling process, which mainly ensures the temperature before entering finish rolling meets the following requirements:

 

≥1180°C for Q steel;

≥1190°C for NQ08 steel;

≥1200°C for Hi-B steel.

 

 

Finish Rolling

 

The key is to control the start rolling and finish rolling temperatures:

 

For Q steel: The start rolling temperature is 1160±20°C, and the finish rolling temperature is controlled above 960°C.

For Hi-B steel: The start rolling temperature is above 1190°C, and the finish rolling temperature is above 960°C (usually controlled above 980°C).

The main objectives of finish rolling are:

 

Generate a large number of dislocations during rolling-these dislocations serve as nucleation sites for MnS precipitation, promoting the formation of finer and more uniformly dispersed MnS particles.

 

Achieve dynamic recrystallization during rolling to completely break down the columnar grains in the casting slab and ensure sufficient recrystallization.

 

 

Coiling

 

After finish rolling, the steel strip is immediately cooled to approximately 550°C with water spray before coiling. This process serves two purposes:

Make carbides (needle-like Fe₃C) distribute dispersedly within the grains, acting as additional inhibitors.

Prevent the precipitation of AlN through post-rolling rapid cooling.

 
 

electrical steel specifications

Raw Material: Our premium CRGO silicon steel is sourced exclusively from renowned manufacturers, Baosteel and WISCO, ensuring top-tier quality for your transformer core laminations.

GRADE we supply:B30P120, B30P105, B30R100, 27QG120, 27QG100, 23Q110, 23QG100, 23QG095, 23RK090, 23RK085, 23QG085, 23RK085, 23QG085, 23RK080, 23RK075, B23R070, 20QG085, 20RK080, 20RK075, B20R070, B20R065,M0H,M1H,M2,M3,M4,M5.
23HP75d, 23HP80d, 23HP85d, 23HP90d, 23HP95d, 23HP100, 23HP100d, 27HP100, 27HP110, 27CG110, 27CG120, 30CG120, 30CG130

Type Grade Width Max Core Loss@P1.7T/50Hz Lamination Factor(%) Min Induction@B800
Common Type 23Q110 35-1200mm 1.10w/kg 97.2 1.82T
23Q120 1.20w/kg 97.2 1.82T
27Q120 1.20w/kg 97.5 1.82T
30G120 1.20w/kg 98 1.82T
High Induction
Type
B20P085 35-1200mm 0.85w/kg 97 1.86T
B23P085 0.85w/kg 97.2 1.88T
B23P090 0.90w/kg 97.2 1.88T
B23P095 0.95w/kg 97.2 1.88T
B23P100 1.00w/kg 97.2 1.88T
B27P095 0.95w/kg 97.5 1.89T
27QG100 1.00w/kg 97.5 1.89T
B30P105 1.05w/kg 98 1.89T
Domain Refined High Induction
Type(Laser)
B20R070 35-1200mm 0.70w/kg 97 1.86T
B23R085 0.85w/kg 97.2 1.88T
B27RK085 0.85w/kg 97.5 1.89T

We meticulously calculate and regularly update quotations based on your comprehensive drawings, ensuring precision and cost-effectiveness in every transaction.
Upon receiving your confirmation, we seamlessly transition into production, adhering stringently to the meticulously detailed drawings you provide to ensure flawless execution.

 

 

 

GNEE Featured Products

Gnee provides premium iron cores to the world. Our cores can be selected in a wide range of materials, shapes, applications, manufacturing techniques, etc., to meet customers' diverse demands. Explore our wide product range now~

Manufacturing Process

 

Raw Material Sourcing

1. Raw Material Sourcing

Slitting

2. Slitting

Punching

3. Punching

Laminating

4. Laminating

Core Forming

5. Core Forming

testing

6. testing

GNEE New Material

Founded in 2008 and located in Anyang in China, GNEE New Material is a high-tech enterprise specializing in researching and manufacturing iron core products.
The company currently occupies over 20,000 square meters and employs more than 200 people, including over 80 professionals. After more than 18 years of development, we have built our own magnetic material production base and independently develope, produce, and sell various kinds of iron cores. The common types include silicon steel cores, motor cores, transformer cores, toroidal iron cores, special-shaped cores, custom cores, and others. Our cores are widely applied in different sectors including transformers, motors, mutual inductors, voltage stabilizers, welding machines, magnetic amplifiers, and instrumentation, providing diverse core solutions to global customers.

GNEE New Material

30+

Types of Products

18k+

Happy Clients

 

 

 

Why Choose GNEE New Material?

 

GNEE New Material was founded in 2008, which is a National High-tech Enterprise & Famous Brand Enterprise in China, developing into a professional manufacturer and supplier of high-quality iron cores.

 

18+

Over 18 years of success in the iron core industry;
National High-tech Enterprise & Famous Brand Enterprises in China;

 
 

200+

Over 200 employees;
The R&D team has more than 80 experienced engineers and the production team has more than 100 skilled staffs;

 
 

35+

Annual turnover up to 35 million dollor per year;
Owns many sets of highly automatic winding, annealing, and assembling machines;

 
 

1,000+

Over 1000 customers in domestic and overseas markets;
core Products are exported to more than 70 countries in the world;

 

GNEE New Material Factory Overview

GNEE New Material Factory
GNEE New Material Factory
GNEE New Material Factory
GNEE New Material Factory
GNEE New Material Factory
GNEE New Material Factory

Meet Our Sales Manager

 

"The Core of the Iron Core, the Power of Leadership" - See Our Great Decision-Makers Deeply Engaged in the Magnetic Materials Industry.

CEO

Edison Zhang

CEO

General Manager

Kelly Zhang

General Manager

Sales Manager

Alex Cao

Sales Manager

 

 

Industries Served

 
Automobile Industry

Automobile Industry

New Energy

New Energy

Motor Applications
Motor Applications
Transformer Applications

Transformer Applications

modular-1

Our Mission

Strive To Create world-class Iron core brand

With 18 Years of industry experience, we focus on the research, development, and manufacturing of high-quality iron cores for electricity, industrial control, new energy, and automotive markets

Send Inquiry