Slitted Grain Oriented Silicon Steel M1 0.23mm 0.80W/kg
Nov 18, 2026
Leave a message
What is Slitted Grain Oriented Silicon Steel M1 0.23mm 0.80W/kg?
Slitted Grain Oriented Silicon Steel M1 0.23mm 0.80W/kg is a premium grade of cold rolled grain oriented (CRGO) electrical steel that has been precision slit longitudinally from a master coil to custom widths. The "M1" designation refers to a high-permeability grade (equivalent to modern Hi-B or laser-scribed grades), "0.23mm" is the material thickness, and "0.80W/kg" is the guaranteed maximum core loss at 1.7 Tesla and 50Hz frequency.
![]()
Grain oriented silicon steel is an iron-silicon alloy containing approximately 3–3.5% silicon, manufactured through a sophisticated process of cold rolling and high-temperature annealing that aligns the crystal grains in a single direction (Goss texture). This grain alignment gives the material dramatically higher magnetic permeability and lower core loss along the rolling direction - exactly what transformer cores need since magnetic flux travels in a fixed direction around the core loop.
💡 Pro Tip: The 0.80 W/kg core loss rating at 1.7T/50Hz places this material in the top tier of commercially available CRGO grades. To put this in perspective: a standard M4 grade (0.23mm) is typically rated at 0.95 W/kg, while this M1 grade at 0.80 W/kg delivers approximately 16% lower core loss. For a 100 MVA power transformer, that difference translates to roughly 50–80 kW in reduced no-load loss - a massive energy saving over the transformer's 30-year service life.
Specification of Slitted Grain Oriented Silicon Steel M1 0.23mm 0.80W/kg
| Parameter | Specification |
|---|---|
| Product Name | Slitted Grain Oriented Silicon Steel M1 0.23mm 0.80W/kg |
| Grade | M1 (Hi-B Laser-Scribed equivalent, e.g., 23QG080) |
| Thickness | 0.23 mm (±0.015 mm tolerance for prime grade) |
| Core Loss (P1.7/50Hz) | ≤0.80 W/kg (guaranteed) |
| Magnetic Induction (B8) | ≥1.87 T (high permeability Hi-B grade) |
| Slit Width Range | 10 mm – 1,250 mm (custom widths to your specification) |
| Width Tolerance | ±0.1 mm (precision) / ±0.2 mm (standard) |
| Edge Condition | Slit Edge (SE) - precision sheared, burr-controlled |
| Burr Height | ≤0.015 mm (premium slitting quality) |
| Camber | ≤5 mm per 2,000 mm length |
| Coil Weight | 1 – 8 MT per slit coil (custom small coils: 0.5 – 3 MT available) |
| Coil ID | 300 mm / 400 mm / 508 mm / 610 mm (custom IDs available) |
| Surface Coating | C-5 / C-6 phosphate insulation coating |
| Domain Refinement | Laser-Scribed (Hi-B domain-refined) |
| Silicon Content | 3.0 – 3.5% |
| Lamination Factor | ≥96% |
| Delivery Condition | Slit and rewound, fully annealed, ready for core production |
| Lead Time | 10 – 20 working days from stock master coils |
| Certification | Mill Test Certificate (MTC) + Slitting Quality Inspection Report |
| Standards Compliance | IEC 60404-8-7, ASTM A976/A976M, JIS C 2553 |

Advantages of Slitted M1 Grade 0.23mm CRGO Silicon Steel (0.80 W/kg)
1. Ultra-Low Core Loss Maximizes Transformer Efficiency
With a guaranteed core loss of just 0.80 W/kg at 1.7T/50Hz, this M1 grade material is among the lowest-loss commercially available CRGO silicon steels. The laser-scribed domain refinement process narrows the 180° magnetic domain walls, reducing anomalous eddy current loss by approximately 10–15% compared to non-laser Hi-B grades.
2. High Magnetic Permeability Enables Compact Core Design
The M1 grade's high magnetic induction (B8 ≥ 1.87 Tesla) means the core can operate at higher flux densities without excessive core loss. This allows transformer designers to reduce the core cross-sectional area - and therefore the total core weight - by 8–12% compared to standard CGO grades.
3. Precision Slitting Quality Ensures Optimal Core Performance
Our M1 grade 0.23mm CRGO steel is slit on dedicated electrical steel lines with precision knife clearance control, achieving burr heights of ≤0.015mm - well below the industry standard of 0.03mm. This is critical because excessive burrs cause inter-lamination short circuits that increase eddy current loss and can lead to localized hotspots.
Pro Tip: When evaluating suppliers of 0.80 W/kg CRGO material, always request actual test data from recent production coils, not just the nominal grade rating.
Looking for premium M1 grade 0.23mm CRGO silicon steel with guaranteed 0.80 W/kg core loss and precision slitting? Get a technical quotation with mill test certificate samples and slitting quality specifications - delivered within 24 hours.
Electrical Steel Application - Power Transformer Cores
When it comes to high-performance power transformer cores - particularly those used in high-voltage substations, generator step-up (GSU) transformers, and critical infrastructure - the electromagnetic performance of the core steel is the single most important factor determining transformer efficiency, size, and total cost of ownership. Let's examine how slitted M1 grade 0.23mm CRGO steel with 0.80 W/kg core loss performs in this demanding application.
The M1 grade with 0.80 W/kg core loss achieves its exceptional performance by optimizing all three loss components: high-silicon formulation (3.0–3.5%) reduces hysteresis loss, the 0.23mm thin gauge reduces classical eddy current loss, and laser domain refinement reduces anomalous eddy current loss. The result is a material that delivers approximately 15–20% lower total core loss than standard 0.23mm CGO grades.

Performance in 110kV–220kV Power Transformer Cores
For a typical 50 MVA, 110kV power transformer core constructed with slitted M1 grade 0.23mm CRGO steel (0.80 W/kg at 1.7T/50Hz), operating at a design flux density of 1.65T:
- Core weight: Approximately 28–32 tonnes
- No-load loss: Approximately 18–20 kW (at operating flux density)
- Exciting current: Typically 0.25–0.4% of rated current
- Noise level: Achievable ≤55 dB(A) with proper core design and clamping
- Efficiency at 50% load: Exceeds 99.75%
- Total loss at rated load: Approximately 200–220 kW (core + load loss)
Compared to the same transformer built with standard M4 grade 0.23mm CRGO (0.95 W/kg), the M1 grade reduces no-load loss by approximately 15–18%, saving roughly 3–4 kW of continuous power loss. Over a 30-year service life, this adds up to about 800,000 – 1,050,000 kWh of saved energy - at typical industrial electricity rates, that's $80,000–$120,000 in savings per transformer, far exceeding the material cost premium.
M1 0.23mm Slitted CRGO Price
Market analysis for H2 2026 indicates that Hi-B and laser-scribed CRGO prices are expected to remain firm or increase slightly (0–8%), driven by continued strong demand from utility and renewable energy transformer manufacturers. Global average electrical steel prices are forecast in the range of USD 1.75–1.95/kg for the second half of 2026, with premium Hi-B laser-scribed grades at the upper end of this range .
Approximate Price Range for Slitted M1 Grade 0.23mm (0.80 W/kg)
| Product Form | Price Range (USD/MT) | Notes |
|---|---|---|
| Prime Master Coil (Mill Edge) | $2,100 – $2,450 | Full-width coil, full MTC, base price |
| Slit Coil (precision slitting) | $2,250 – $2,600 | + $100–200/MT slitting premium |
| Small Rewound Slit Coil | $2,350 – $2,750 | + additional $80–150/MT rewinding |
| Cut-to-Length Sheets | $2,400 – $2,800 | + shearing premium, includes end trimming |
| Secondary / Non-Prime (if available) | $1,700 – $2,050 | 15–20% discount, limited availability for M1 grade |
Note: Prices are indicative FOB China basis, valid as of 2026 Q4 estimate. Actual prices vary by order quantity, slit width, number of slits per coil, coil weight, payment terms, and current market conditions. M1 grade 0.80 W/kg is a premium product with limited supply - we recommend placing orders 45–60 days ahead of your production schedule to ensure availability.
💡 Pro Tip: For M1 grade 0.80 W/kg material, the price difference between master coils and slit coils is only 5–8% - but the convenience and quality assurance of professionally slit material typically delivers much more value than the additional cost. In-house slitting of high-grade CRGO requires specialized equipment and expertise, and a single slitting quality issue can ruin an entire expensive coil. For premium grades, professional slitting from your supplier is almost always the better choice.
Need current pricing and availability for M1 grade 0.23mm CRGO with 0.80 W/kg core loss? Get a real-time quotation with transparent pricing breakdown and delivery timeline - no hidden fees, no surprises.
Why Choose GNEE New Material?
Flexible coil specifications: We supply prime quality, concession/off-grade, jumbo coils (12–15 tons), and small/mini coils (from 50 kg upward) to suit different production volumes and cost requirements.

In-house precision processing lines: Equipped with slitting, cut‑to‑length, automatic lamination stacking, laser cutting, edge finishing, and narrow strip recoiling equipment, supporting high‑precision customisation.

Core processing services: We offer precision slitting, cut‑to‑length blanking, laminated core stacking (limbs + yokes) per your drawings, and narrow strip pancake coil winding – delivering semi‑finished or fully assembled components.

Edge finishing options: Available in as‑rolled/mill edge, sheared/trimmed edge, slit edge, dressed/finished edge, deburred edge, square/right‑angle edge, rounded edge, chamfered edge, laser‑cut edge, and punched/stamped edge – meeting various insulation and voltage withstand requirements.
GNEE New Material – Packaging and shipping
1. Coil Weight < 4 Tons
Inner & outer special air anti-corrosion paper
Overall thin plastic film sealing
Internal & external paper corner protectors, end covers and surrounding protection plate
Inner & outer metal angle protection rings
2. Coil Weight ≥ 4 Tons
Based on the above packaging, an extra external buffer board is added for enhanced anti-collision protection.
All packaging is seaworthy, protecting coils from rust, scratches and deformation during long-distance transportation.
Ready to source premium M1 grade 0.23mm slitted CRGO silicon steel with guaranteed 0.80 W/kg core loss for your transformer production? From grade selection to custom slitting to export delivery - our technical sales team will design a tailored package for your specific requirements.
FAQ
Q1: What does "M1 grade" mean in grain oriented silicon steel?
A: "M1" is a historical grade designation for high-permeability grain oriented silicon steel. The "M" stands for magnetic quality, and the number "1" indicates the highest permeability tier in the M-grade system. M1 grade corresponds to modern Hi-B (High Permeability) laser-scribed grades with core loss around 0.80 W/kg at 1.7T/50Hz for 0.23mm thickness. Modern grade naming systems use codes like 23QG080 (23 = 0.23mm, Q = quality/grain-oriented, G = Hi-B high permeability, 080 = 0.80 W/kg). M1 grade represents the top tier of commercially available CRGO material, specified for the highest-efficiency transformer designs.
Q2: Is 0.80 W/kg core loss measured at 1.5T or 1.7T?
A: Our M1 grade 0.23mm CRGO steel's 0.80 W/kg core loss rating is measured at 1.7 Tesla and 50Hz (P1.7/50), which is the standard industry reference point for CRGO grade specification. It's very important to always confirm the test conditions when comparing core loss values - the same material tested at 1.5T would show much lower loss (approximately 0.55–0.60 W/kg), and comparing values at different flux densities is misleading. Always request mill test certificates that clearly state both the induction level and frequency, and compare only values measured at the same conditions.
Q3: What is the minimum order quantity for slitted M1 grade 0.23mm CRGO?
A: For slitted M1 grade 0.23mm material, the minimum order is typically 1 MT total per slitting setup, with minimum 200–300 kg per individual width. However, because M1 grade 0.80 W/kg is a premium grade with more limited stock availability, we recommend ordering at least 3–5 MT to ensure we can source the right base material. Smaller trial quantities (200–500 kg) may be available for product development purposes - please inquire about our sample program. For custom mill orders of M1 grade, the MOQ is typically one full production lot (20–30 MT).

