High Permeability Ring Type Iron Core for Electric Transformer
Oct 15, 2025
Leave a message
Ring Type Iron Core
A ring type iron core is a basic magnetic component made by processing ferromagnetic materials into a closed ring structure. Leveraging its core advantages of low magnetic leakage and uniform magnetic field, it is widely used in power and electronic equipment that requires efficient magnetic coupling.

ring Core Structure and Performance Characteristics
The performance advantages of ring type iron cores fully rely on their structural design and material properties, which together determine the adaptability of their application scenarios.
Closed Magnetic Circuit Design: The ring structure has no obvious air gaps, and its magnetic reluctance is much lower than that of traditional iron cores such as EI-type and C-type. This can significantly reduce magnetic flux leakage, with the magnetic leakage rate usually controlled below 5%, improving the efficiency of magnetic energy utilization.
Uniform Magnetic Field Distribution: The symmetry of the ring geometry makes the magnetic flux density distribution inside the core more balanced. This avoids local overheating caused by concentrated local magnetic flux and reduces noise generated by electromagnetic vibration.
Strong Material Adaptability: Different ferromagnetic materials can be selected according to application requirements, ranging from low-cost silicon steel sheets to nanocrystalline alloys and ferrites with low high-frequency loss. This covers all scenario needs from power frequency to high frequency.
Main Material Types and Applicable
Ring type iron cores made of different materials have significant performance differences, which directly determine their applicable frequency ranges and equipment types. The specific corresponding relationships are as follows:
1.Silicon Steel Sheet Ring Type Iron Core:
Mainly composed of iron and silicon (silicon content: 1.5%-4.5%), it has moderate magnetic permeability and low cost. It is suitable for power frequency (50/60Hz) scenarios, such as power frequency transformers and AC contactors.
2.Nanocrystalline Alloy Ring Type Iron Core:
Made of iron-based alloys with nanoscale crystal structures, it has extremely low high-frequency loss and high magnetic permeability. It is suitable for medium-to-high frequency (1kHz-1MHz) scenarios, such as on-board chargers and high-frequency switching power supplies.
3.Ferrite Ring Type Iron Core:
With iron oxide as the main component, it has high resistivity and low high-frequency loss, but low saturation magnetic flux density. It is suitable for ultra-high frequency (above 1MHz) scenarios, such as RF antennas and high-frequency filter inductors.
Toroidal Core Application
The application of ring type iron cores covers multiple fields such as power, electronics, and new energy. Its core is to use its efficient magnetic coupling characteristics to improve equipment performance.
- Power System: Used as the magnetic core of distribution transformers and current transformers, it reduces losses during power transmission and ensures the accuracy of power metering.
- Electronic Equipment: Applied in transformers and filter inductors of switching power supplies, as well as audio transformers of audio equipment. It reduces the interference of power noise on signals and improves the purity of audio signals.
- New Energy Field: Serves as a filter magnetic core in photovoltaic inverters and energy storage converters, adapting to the medium-to-high frequency energy conversion needs and contributing to the miniaturization of equipment.
- Industrial Control: Used in encoders of servo motors and signal coupling magnetic cores of sensors to ensure stable transmission of control signals.
ring Core specification
![]()
| Magnetic core size(mm) | Protective box size(mm) | Effective cross-sectional area Ae(mm2) | Magnetic path length Ie(mm) | Maximum DC overcurrent class (A) |
||||||
| id | od | ht | ID | OD | HT | |||||
| 14 | 19 | 6.5 | 12 | 22 | 8 | 11.86 | 51.81 | 20 | ||
| 14 | 20 | 10 | 12 | 22.3 | 11.4 | 29.68 | 52.29 | 40 | ||
| 16 | 21 | 10 | 15 | 24 | 12.3 | 24.85 | 57.41 | 60 | ||
| 16 | 23 | 8 | 15 | 24 | 9.7 | 20.44 | 61.23 | 60 | ||
| 16 | 23 | 10 | 15 | 24 | 12.3 | 34.62 | 59.92 | 60 | ||
| 17 | 22 | 10 | 15.3 | 24.4 | 12.3 | 24.86 | 60.59 | 60 | ||
| 17 | 21 | 8 | 15.3 | 24 | 9.7 | 25.56 | 60.67 | 60 | ||
| 17 | 23 | 8 | 15.3 | 24.4 | 9.7 | 26.89 | 61.34 | 60 | ||
| 18 | 23 | 10 | 16.4 | 24.4 | 12.3 | 29.78 | 60.38 | 70 | ||
| 18 | 24 | 9 | 16.4 | 25 | 11.2 | 34.78 | 60.89 | 70 | ||
| 18 | 25 | 10 | 16.4 | 25.9 | 12.3 | 37.97 | 64.56 | 70 | ||
| 19 | 24 | 9 | 17.3 | 25 | 11.2 | 40.39 | 65.32 | 80 | ||
| 19 | 25 | 10 | 17.3 | 26 | 12.3 | 39.42 | 62.31 | 80 | ||
| 19 | 26 | 10 | 17.3 | 27.3 | 12.3 | 48.32 | 69.56 | 80 | ||
| 20 | 25 | 10 | 18.5 | 26.3 | 12.3 | 39.29 | 70.32 | 90 | ||
| 20 | 28 | 10 | 18.5 | 29 | 12.3 | 45.76 | 73.88 | 90 | ||
| 20 | 32 | 10 | 18.5 | 32.3 | 12.3 | 58.91 | 78.75 | 90 | ||
| 21 | 29 | 10 | 18.2 | 31.3 | 12.3 | 39.65 | 77.19 | 100 | ||
| 21 | 26 | 8 | 18.3 | 27.4 | 9.7 | 46.54 | 78.32 | 100 | ||
| 21 | 28 | 10 | 18.3 | 30 | 12.3 | 50.39 | 77.45 | 100 | ||
| 22 | 28 | 10 | 20.5 | 30 | 12.3 | 49.32 | 79.89 | 120 | ||
| 22 | 32 | 10 | 20.5 | 33.4 | 12.3 | 43.58 | 73.43 | 120 | ||
| 23 | 32 | 10 | 21.3 | 33.4 | 12.3 | 44.56 | 74.56 | 120 | ||
GNEE Featured Products
Gnee provides premium iron cores to the world. Our cores can be selected in a wide range of materials, shapes, applications, manufacturing techniques, etc., to meet customers' diverse demands. Explore our wide product range now~
Manufacturing Process

1. Raw Material Sourcing

2. Slitting

3. Punching

4. Laminating

5. Core Forming

6. testing
GNEE New Material
Founded in 2008 and located in Anyang in China, GNEE New Material is a high-tech enterprise specializing in researching and manufacturing iron core products.
The company currently occupies over 20,000 square meters and employs more than 200 people, including over 80 professionals. After more than 18 years of development, we have built our own magnetic material production base and independently develope, produce, and sell various kinds of iron cores. The common types include silicon steel cores, motor cores, transformer cores, toroidal iron cores, special-shaped cores, custom cores, and others. Our cores are widely applied in different sectors including transformers, motors, mutual inductors, voltage stabilizers, welding machines, magnetic amplifiers, and instrumentation, providing diverse core solutions to global customers.

30+
Types of Products
18k+
Happy Clients
Why Choose GNEE New Material?
GNEE New Material was founded in 2008, which is a National High-tech Enterprise & Famous Brand Enterprise in China, developing into a professional manufacturer and supplier of high-quality iron cores.
18+
Over 18 years of success in the iron core industry;
National High-tech Enterprise & Famous Brand Enterprises in China;
200+
Over 200 employees;
The R&D team has more than 80 experienced engineers and the production team has more than 100 skilled staffs;
35+
Annual turnover up to 35 million dollor per year;
Owns many sets of highly automatic winding, annealing, and assembling machines;
1,000+
Over 1000 customers in domestic and overseas markets;
core Products are exported to more than 70 countries in the world;
GNEE New Material Factory Overview






Meet Our Sales Manager
"The Core of the Iron Core, the Power of Leadership" - See Our Great Decision-Makers Deeply Engaged in the Magnetic Materials Industry.

Edison Zhang
CEO

Kelly Zhang
General Manager

Alex Cao
Sales Manager
Industries Served

Automobile Industry

New Energy


Transformer Applications

Our Mission
Strive To Create world-class Iron core brand
With 18 Years of industry experience, we focus on the research, development, and manufacturing of high-quality iron cores for electricity, industrial control, new energy, and automotive markets











