Innovation and Application of Silicon Steel Annealing Furnace Technology for New Energy Vehicles
Feb 05, 2024
Leave a message
Background: The Demand for Motor-Grade Silicon Steel
Silicon steel is an indispensable soft magnetic material for the power, electronics and automotive industries. The rapid growth of the new energy vehicle market has driven explosive demand for non-oriented silicon steel used in traction motor stators and rotors. Ultra-thin non-oriented grades improve motor efficiency and reduce iron loss, but they place much stricter demands on the annealing process than ordinary grades. When thin strip and high-grade products share one annealing line, the heating rate is too low, the oxidation of the strip is not controlled, and the temperature uniformity is poor, which leads to unstable iron loss values and low output. These production bottlenecks made a dedicated annealing furnace technology necessary.
Process Requirements of Ultra-Thin Non-Oriented Silicon Steel
Annealing of motor-grade non-oriented silicon steel must meet a demanding process window: a heating rate of at least 30 C/s, a controlled cooling rate of no more than 10 C/s, a furnace atmosphere with a hydrogen ratio of about 90%, and hydrogen flow through the cooling section. The strip temperature deviation must stay within about 5 C across the width and along the length, otherwise the magnetic properties vary from coil to coil. The furnace pressure also has to be stable enough to keep the high-hydrogen atmosphere safe and to prevent oxidation of the strip surface.
Key Technical Innovations
High-Frequency Induction Heating with Protective Atmosphere
An induction heating power supply using series resonance and intelligent closed-loop control was developed to heat the strip quickly and uniformly inside a protective atmosphere. The contact-free sensor design eliminates the electric shock risk of conductive contact sensors, and the series-resonant inverter simplifies open-circuit and short-circuit protection. With closed-loop temperature control, the strip temperature deviation is held within 5 C, which was previously only achievable with imported equipment.
Green and Efficient Indirect Heating
For the high-temperature sections, radiant tube burners were improved so that the thermal efficiency at 1050 C reaches 65-70%, about 5 percentage points higher than conventional designs. The introduction of diffusion combustion and a continuous-ratio plus pulse combustion control strategy holds the furnace temperature within 4 C, while nitrogen oxide emissions are reduced by about 50 mg/Nm3 and stabilized below 150-180 mg/Nm3 at 8% base oxygen, supporting low-carbon production.
Precise Cooling Control
An online intelligent optimization control system manages the cooling section so that the strip is cooled at the required rate without edge wave defects. Edge wave, a flatness defect caused by uneven cooling across the strip width, is eliminated, and the magnetic quality of the finished material is improved.
Furnace Pressure and Atmosphere Control
Innovative furnace pressure control equipment improved the pressure stability by about 50%, holding the fluctuation in the range of -3 Pa to +4 Pa, which is required for a 90% hydrogen atmosphere. This stable pressure prevents air ingress, protects the strip from oxidation and keeps the process safe.
Impact on Motor Performance and the Industry
With the new annealing technology, the full range of non-oriented silicon steel for electric vehicles can be produced on a dedicated line with stable iron loss and good flatness. Lower core loss in the stator and rotor directly raises the efficiency of the traction motor and extends the driving range of the vehicle. The integrated innovation of induction heating, indirect heating, controlled cooling and atmosphere control also upgraded the domestic annealing furnace technology and strengthened the competitiveness of metallurgical equipment in the international market.
Frequently Asked Questions
Why does a new energy vehicle motor need ultra-thin non-oriented silicon steel?
Traction motors run at high speed and high frequency. Thinner gauge steel reduces the eddy current loss in the core, which lowers the motor temperature and improves the efficiency and the continuous output of the drive.
Why is a hydrogen atmosphere used in the annealing furnace?
Hydrogen prevents oxidation of the strip surface and improves the magnetic properties of the annealed steel. A high hydrogen ratio, around 90%, requires a gas-tight furnace and precise pressure control for safety.
What is the advantage of induction heating in strip annealing?
Induction heating heats the strip directly and quickly, achieving the high heating rate and the uniform temperature profile that thin motor-grade steel needs, with less energy consumed on heating the furnace structure itself.
How does cooling control affect the strip quality?
The cooling rate determines the final microstructure and the internal stress of the steel. Uneven cooling produces edge wave and residual stress, which degrade the flatness and the magnetic uniformity of the finished strip.
What does the iron loss of motor steel depend on?
Iron loss depends on the chemical composition, the grain size after annealing, the thickness of the strip and the insulation coating. The annealing temperature profile and the atmosphere determine the final grain structure and therefore the loss level.
Does this technology also apply to grain-oriented silicon steel?
Grain-oriented steel uses a different annealing route that develops the Goss texture, usually in a batch or continuous decarburization and high-temperature box annealing process. The induction heating and atmosphere control principles can be shared, but the process windows are specific to each product family.

