Silicon Steel Opportunities in Carbon Neutrality and Efficiency Upgrades

Feb 05, 2024

Leave a message

Why Carbon Neutrality Reshapes Electrical Steel Demand

Carbon peak and carbon neutrality programmes are changing the structure of the power sector rather than simply adding capacity. Two mechanisms dominate: a rising share of wind and photovoltaic generation in the supply mix, and a sustained effort to cut losses in transmission, distribution and industrial equipment. Both mechanisms run through the same material family, cold-rolled electrical steel, because every transformer, generator and motor core in the chain depends on it.

Independent analyses indicate that power generation and heating account for roughly 40% of emissions in large economies, while industry consumes about two thirds of final energy. Those proportions explain why efficiency rules for transformers and motors have become the practical lever for decarbonization.

Two Levers: More Renewable Generation and Lower Losses

On the supply side, renewable additions require step-up transformers for wind and solar farms, collector substations and large power transformers at the grid interface. On the demand side, efficiency regulations push distribution transformers and industrial motors to ever lower loss classes, including IE4 and IE5 efficiency levels defined in IEC 60034-30-1, and transformer energy efficiency grades in GB 20052.

Both levers consume the same raw material in greater volume and in higher grades, which is why electrical steel is one of the few materials whose demand rises with both the growth of generation and the tightening of efficiency limits.

Silicon Steel: The Core Material of the Energy Transition

Electrical steel divides into grain-oriented (GO) and non-oriented (NO) families. Grain-oriented material, particularly the high-permeability Hi-B type, is used almost exclusively in transformer cores because the Goss texture aligns magnetic domains with the rolling direction and produces very low core loss at low magnetizing force. Non-oriented material carries flux in many directions and serves rotating machines, where the flux path rotates rather than staying along one axis.

Grain-oriented strip: typical thickness 0.18 mm to 0.35 mm, specified by core loss at 1.7 T and 50 Hz.

Non-oriented strip: typical thickness 0.35 mm to 0.65 mm, specified by core loss at 1.5 T and 50 Hz.

Relevant standards: GB/T 2521.1 and IEC 60404-8-7 for grain-oriented grades, GB/T 2521.2 and IEC 60404-8-4 for non-oriented grades, with loss measured by the Epstein method or single sheet tester.

Grade Segmentation and Application Fit

Segment Typical application Demand driver
Hi-B grain-oriented steel Large power transformers, high-efficiency distribution transformers Renewable step-up and grid upgrade projects
Conventional grain-oriented steel Standard distribution transformers Baseline grid replacement
High-grade non-oriented steel IE4 and IE5 motors, electric vehicle traction motors, generators Motor efficiency regulation and electrification
Medium and low-grade non-oriented steel General industrial and household motors Mature, price driven replacement demand

The market split matters more than the headline tonnage. Since late 2021 the price gap between premium and commodity electrical steel has widened, and allocation of Hi-B and high-grade non-oriented capacity has become the constraint for transformer and motor builders.

Demand Elasticity by Segment

Industry analyses put the demand elasticity of the four segments in the order Hi-B grain-oriented steel, then high-grade non-oriented steel, then conventional grain-oriented steel, then medium and low-grade non-oriented steel, with indicative values of about 18%, 16%, 6% and 5% respectively. These figures are indicative estimates rather than forecast guarantees, and any capital decision should be checked against current market data.

Grain-oriented material scores highest because transformers sit directly on the renewable and grid efficiency route. High-grade non-oriented material follows because electric vehicle traction motors and IE5 industrial motors both require low-loss cores that only premium grades deliver at volume.

Grade Selection and Supply Planning

Match core loss class to the target transformer efficiency grade or motor efficiency class instead of buying by thickness alone.

Check the guaranteed loss value at the specified induction and frequency, and request mill test reports for each heat number.

Confirm the coating type and stacking factor, which affect interlaminar loss and core building cost.

Plan slitting and cut-to-length capacity in advance, since wide coil availability limits narrow core widths.

For export equipment, verify that the selected grade meets both the local efficiency regulation and the destination market requirement.

Frequently Asked Questions

Q: Why does Hi-B grain-oriented steel command a price premium?
Because its sharper Goss texture and thinner gauge give lower core loss and lower magnetizing current. For a transformer, that translates directly into a better efficiency grade and a smaller core for the same rating.

Q: Which grade family is used in electric vehicle motors?
High-grade non-oriented electrical steel, usually 0.20 mm to 0.35 mm thick, chosen for low loss at high frequency and sufficient mechanical strength for rotor spinning.

Q: Does a thinner gauge always reduce total losses?
Not necessarily. Thinner strip reduces eddy current loss but can raise hysteresis loss through higher stress sensitivity, and it increases stacking cost. Selection must balance core loss, stacking factor and manufacturing cost.

Q: How are electrical steel losses specified?
By the specific total loss in watts per kilogram at a stated induction and frequency, together with the magnetic polarization at a stated field strength, measured under the test method defined in IEC 60404-2 or IEC 60404-3.

Q: What drives demand elasticity differences between the four segments?
The end product cycle. Transformers are tied to grid and renewable construction, while motors are tied to industrial replacement cycles and vehicle electrification, so their demand responds differently to efficiency regulation.

Q: How should procurement react to tighter efficiency rules?
Secure qualified premium grade supply early, qualify two sources for each thickness, and verify incoming coil certificates against the grade specified for the efficiency class being claimed.

Send Inquiry