112 kVA 11 kV Oil Immersed Distribution Transformer: 11 kV to 0.4 kV Step-Down Design
Nov 10, 2025
Leave a message
112 kVA, 11 kV to 0.4 kV Step-Down Duty
A 112 kVA oil-immersed distribution transformer with an 11 kV primary and a 0.4 kV secondary is a step-down unit sized for a single commercial or light-industrial load point. The rating matches a common generator and inverter frame size as well as a typical pole-mounted distribution requirement, so it appears both in utility networks and in captive installations where a private 11 kV feeder has to be reduced to the utilisation voltage of a building or processing plant.
The LV line current at 400 V is approximately 162 A (112000 / (1.732 x 400)), which sets the rating of the incoming LV protective device and the cross-section of the LV cabling between the transformer and the main distribution board.
Winding Material and Coil Construction
Copper is used on both windings. The HV winding is wound from enamelled copper wire in a multi-layer cylindrical arrangement with interleaved insulation cylinders, which distributes the impulse voltage stress along the winding rather than concentrating it between adjacent turns. The LV winding uses copper foil; the wide, thin foil presents a large conduction area for the low-voltage, high-current circuit and simultaneously acts as an electrostatic shield between the two windings, which reduces the transfer of high-frequency transients from the HV side.
Windings are assembled into the laminated core, and insulation is applied where the electrical field requires it using pressboard, cylinders and end blocks. Core bolts and tie rods are locked in position to prevent loosening under repeated short-circuit forces. The complete core-and-coil assembly is held in a hot-air drying chamber at elevated temperature so that moisture is driven out of the cellulose insulation before the unit is vacuum impregnated and filled with oil.
| Parameter | Value |
|---|---|
| Rated capacity | 112 kVA |
| Primary voltage | 11 kV, Um 12 kV |
| Secondary voltage | 0.4 kV |
| Insulation level, HV (IEC 60076-3) | 75 kV peak lightning impulse, 28 kV rms power-frequency |
| Vector group | Dyn11 |
| Cooling | ONAN, sealed corrugated tank |
| Temperature rise (IEC 60076-2) | 60 K top oil, 65 K average winding |
| Short-circuit withstand (IEC 60076-5) | 2 s symmetrical current |
Sealed Tank and Cooling Behaviour
The transformer is a fully sealed, oil-filled unit with a corrugated tank, intended for outdoor service either on a pole bracket or on a concrete pad. Corrugated fins provide a larger heat-transfer surface than a plain tank of the same footprint, which is why natural oil circulation with natural air circulation is sufficient to meet the temperature-rise limits of IEC 60076-2 at this rating. The same wall compliance absorbs the thermal expansion of the oil, so there is no conservator, no breather and no oil-level gauge to maintain, and the oil remains out of contact with atmospheric oxygen for the whole service interval.
The sealed construction also gives the unit a long interval between interventions, which matters where the transformer is mounted on a pole above a road or in a processing plant where a shutdown is expensive.
Application in Distribution Networks
Typical duties include residential area step-down from an 11 kV spur to the household utilisation voltage, supply to office buildings and commercial complexes with mixed lighting and motor load, and small industrial or mineral processing plants where the load is dominated by motor starting. In all three cases the requirement is the same: a stable secondary voltage under a fluctuating load, and a transformer that can absorb the additional short-circuit and inrush duty imposed by downstream motors.
Off-circuit tapping adjusts the secondary voltage to the actual feeder level. Moving one tap step changes the LV voltage by 2.5 % of the LV nominal, which is enough to correct the voltage drop produced by the difference between the nominal and measured primary voltage.
Testing and Oil Condition
Electrical tests follow the routine test schedule of IEC 60076-1: measurement of winding resistance, ratio and vector group, no-load loss and current, load loss and impedance, applied voltage dielectric test and induced overvoltage test. Insulating oil is supplied to the IEC 60296 mineral oil specification and its power-frequency breakdown voltage is verified by IEC 60156, with ASTM D1816 accepted as an alternative test method for the same property. Dielectric strength, moisture content and acidity are the three parameters that indicate whether the oil still performs both its insulating and its cooling function.
The loading guide IEC 60076-7 provides the temperature basis for deciding how a cyclic load profile - for example a plant that runs two shifts with a heavy afternoon peak - may be carried without exhausting winding insulation life.
Frequently Asked Questions
Q: Is a 112 kVA unit suitable for pole mounting?
A: Yes, at this rating the sealed corrugated tank design is light enough for a two-pole platform. The mounting brackets must be sized for the transformer mass plus the mass of the oil, and the pole must be checked for the short-circuit torque applied at the LV terminals.
Q: Why is copper foil used on the LV winding?
A: Foil gives a high conduction area for a low-voltage, high-current winding and improves the space factor of the coil, so the radial build is reduced. It also shields the LV winding from high-frequency transients coupled from the HV side.
Q: What is the significance of Um equal to 12 kV for an 11 kV winding?
A: Um is the highest system voltage for which the winding insulation is rated. An 11 kV network has a nominal highest voltage of 12 kV, and IEC 60076-3 sets the corresponding test levels at 75 kV peak lightning impulse and 28 kV rms power-frequency.
Q: How much load can the transformer carry in a hot climate?
A: IEC 60076-1 references a maximum ambient of 40 degrees C. Where the site is hotter, the permissible load is reduced so that top-oil and winding hot-spot temperatures stay within the limits of IEC 60076-2 and the ageing assessment of IEC 60076-7.
Q: What causes the oil to deteriorate, and how is it detected?
A: Oxidation, moisture ingress and localised overheating are the main causes. Dissolved-gas analysis in an oil sample detects the early products of each, and IEC 60156 breakdown testing shows whether the dielectric strength is still adequate.
Q: Can the transformer deliver a single-phase load as well as three-phase?
A: With a Dyn11 connection the LV neutral is brought out, so single-phase loads can be supplied up to the rating of each phase winding. Load imbalance between phases should be kept within the limit assumed in the design, because unbalanced loading raises the temperature of the most heavily loaded winding.

