Why Is the Transformer Core Laminated?
Dec 08, 2023
Leave a message
The Problem: Eddy Currents in a Solid Core
When an alternating magnetic flux passes through a solid iron core, it induces circulating currents inside the metal. These eddy currents flow in closed loops perpendicular to the flux, heat the core by I2R dissipation and waste part of the transmitted energy. Because the induced voltage is proportional to the area encircled by the current path, the eddy current loss of a solid core grows with the square of the core thickness and with the square of the operating frequency. A massive one-piece core would therefore run hot and inefficient, and the temperature rise would quickly degrade the insulation of the windings around it.
How Lamination Suppresses Eddy Currents
Lamination solves the problem by slicing the core into thin sheets. Each lamination is coated with a thin electrical insulation layer, typically varnish or an inorganic coating, and the sheets are stacked and clamped into one core. The insulation between the layers blocks the eddy current loops, so the current is confined to the thin cross-section of each individual sheet. This restriction increases the effective resistance of the current path and limits the eddy current to a very small value. The thinner the lamination, the lower the eddy current loss, which is why cores for higher frequencies use progressively thinner sheets.
Lamination Thickness and Stacking Factor
The practical thickness of transformer laminations is a trade-off between loss and manufacturing cost. Power-frequency cores typically use sheets of 0.23 mm to 0.50 mm, with 0.30 mm and 0.35 mm being the most common for grain-oriented silicon steel. When the coating is included, the usable magnetic material is slightly less than the geometric volume; the ratio of effective magnetic cross-section to geometric cross-section is called the stacking factor, usually 0.95 to 0.97 for modern coated laminations. The stacking factor must be considered when the designer calculates the flux density and the number of turns.
Why Silicon Steel Is the Standard Core Material
Silicon steel is used because the addition of silicon to iron raises the electrical resistivity of the material, which directly reduces the eddy current component of the core loss. Grain-oriented silicon steel (GO) is processed to align the magnetic domains in the rolling direction, giving a very low core loss and high permeability along the flux path, and it is the standard material for power transformer cores. The relevant test and specification standards include GB/T 2522 for magnetic property testing, IEC 60404 for magnetic materials and ASTM A876 for grain-oriented electrical steel.
Key Benefits of a Laminated Core
Lower eddy current loss: the insulated thin sheets break the current path and reduce the core loss and the resulting heat generation
Reduced weight and material: the thin insulation layers allow a more compact core than a solid equivalent
Higher efficiency: less energy is wasted as heat, so more of the transmitted power reaches the load
Controlled flux path: the laminated stack concentrates the magnetic flux from primary to secondary winding with less dispersion
The EI Lamination Example
The EI core is a common laminated construction in which E-shaped and I-shaped punchings are interleaved to form the magnetic circuit. The joints between the E and I pieces are staggered from layer to layer, which keeps the air gaps distributed and the reluctance low. EI cores are widely used in transformers, chokes and electromagnetic devices from small control transformers up to medium distribution units, because the punching process is economical and the geometry is easy to wind.
Frequently Asked Questions
What would happen if a transformer core were solid instead of laminated?
The eddy currents would be very large because the current loops could encircle the full core cross-section. The core would overheat rapidly, the efficiency would collapse, and the insulation of the windings would be destroyed by the temperature rise.
Why does eddy current loss increase with frequency?
The induced voltage in the core is proportional to the rate of change of flux, so doubling the frequency doubles the induced voltage and roughly quadruples the eddy current loss for the same flux density. This is why high-frequency magnetic components require very thin laminations or powdered cores.
What is the typical thickness of transformer laminations?
For 50/60 Hz power transformers, 0.30 mm and 0.35 mm grain-oriented sheets are the most common; 0.23 mm and 0.27 mm are used in higher-efficiency designs, while very thin strips below 0.1 mm appear only in high-frequency amorphous and nanocrystalline cores.
What is the stacking factor of a laminated core?
It is the ratio between the effective magnetic cross-section and the geometric cross-section of the stack, typically 0.95 to 0.97, because the insulation coating and the surface roughness occupy a small part of the volume.
Does lamination reduce hysteresis loss?
No. Hysteresis loss depends on the magnetic material itself and on the peak flux density, not on the thickness. Lamination reduces the eddy current loss; hysteresis loss is minimized by material selection and by keeping the flux density within the design range.
How are the laminations insulated from each other?
Grain-oriented silicon steel is supplied with a thin semi-organic or inorganic insulation coating applied by the steel mill. After stamping, the sheets are stacked and clamped so that the coating keeps the layers electrically separated.

