Electric Silicon Steel Coil for Smart Grids: Grade Data, Coatings and Selection
Oct 11, 2025
Leave a message
Why Coil Form Matters in Grid Equipment
Electrical steel reaches its magnetic performance through two mechanisms acting together. Silicon content of roughly 3% in grain-oriented grades raises electrical resistivity, which suppresses eddy currents, while a controlled Goss texture aligns the easy magnetisation direction with the rolling direction, which raises permeability and lowers hysteresis loss along that axis. Delivered in coil form, the material is slit and cut into laminations with the flux path aligned to the rolling direction, so the coil orientation and the finished core orientation are directly linked.
Distribution transformers, pole-mounted and pad-mounted units, inverter reactors on solar and storage feeders, and current transformers in metering equipment all depend on this alignment. Several design habits follow from it: magnetic properties are lost if the steel is over-stressed during slitting or stacking; the insulation coating must survive the core-building process to keep lamination-to-lamination resistance intact; and cutting quality must be controlled because a heavy burr creates a conducting bridge across the coating.
Loss and Induction Data by Grade
The table gives representative grades and their specified loss points. In the standard designation, the number after the grade prefix states the nominal thickness in hundredths of a millimetre and the final number states the maximum specific total loss in W/kg at the stated test point, so the designation is itself a specification.
| Grade type | Nominal thickness | Loss test point | Maximum loss |
|---|---|---|---|
| Grain-oriented, conventional | 0.27 mm | 1.7 T, 50 Hz | 0.90 W/kg |
| Grain-oriented, conventional | 0.23 mm | 1.7 T, 50 Hz | 0.90 W/kg |
| Grain-oriented, high induction | 0.30 mm | 1.7 T, 50 Hz | 1.20 W/kg |
| Non-oriented, fully processed | 0.50 mm | 1.5 T, 50 Hz | 4.70 W/kg |
| Non-oriented, high permeability | 0.50 mm | 1.5 T, 50 Hz | 2.30 W/kg |
| Non-oriented, fully processed | 0.35 mm | 1.5 T, 50 Hz | 4.40 W/kg |
Two points about this table are worth stating plainly. First, non-oriented grades are quoted at 1.5 T while grain-oriented grades are quoted at 1.7 T, so the two families cannot be compared by loss number alone. Second, thickness trades against loss: a 0.23 mm grain-oriented grade and a 0.27 mm grade may carry the same loss figure, but the thinner material also gives a higher stacking factor penalty and a higher cost per tonne, which is why the choice is made on total cost of ownership of the finished transformer.
Thickness Tolerance, Flatness and Burr
Three dimensional characteristics dominate core-building yield. Thickness is specified with a tolerance band and a maximum variation within a coil, because thickness variation changes the stacking factor and therefore the effective cross-section. Flatness and residual curvature govern how evenly laminations stack and how much air is trapped between them; edge wave is the usual cause of an out-of-spec stack. Burr height at the cut edge must stay small, since a burr that penetrates the coating shorts adjacent laminations and produces a local hot spot that grows over service life. Purchasing specifications should state all three limits numerically rather than by description.
Insulation Coatings and Stacking Factor
The coating is not a cosmetic layer; it sets the interlaminar resistance that limits eddy-current circulation between laminations. Coatings for grain-oriented material range from thin inorganic types for wound cores through to thicker coatings that must withstand stress-relief annealing and then resist oil and heat in service. Coating classification is defined in ASTM A976, which assigns coating types and thickness classes, and the choice must match the manufacturing route: a coating designed for annealing behaves differently from one intended for use as-cut. Coating thickness also reduces the stacking factor, so a heavier coating lowers the effective magnetic cross-section even though it improves interlaminar resistance. Reported stacking factors for thin grain-oriented material typically fall in the 0.955-0.97 range depending on thickness and coating class, and the value should always be tied to a stated measurement method.
Applications Across Smart Grid Equipment
Distribution and pole-mounted transformers: wound or stacked grain-oriented cores, where loss at 1.7 T and 50 Hz is the primary selection criterion and noise from magnetostriction is a secondary one.
Solar and storage inverter reactors: non-oriented grades in 0.35-0.50 mm thickness, where the flux path is not aligned with the rolling direction and a higher saturation induction is not required.
Electric vehicle charger magnetics: thin non-oriented grades that keep eddy-current loss low at several hundred hertz to a few kilohertz of ripple.
Metering current transformers and instrument transformers: high-permeability grades at low flux density, where accuracy class rather than loss governs selection.
Substation auxiliary and earthing transformers: conventional grain-oriented grades where cost per tonne dominates and loss limits are set by efficiency regulation.
Handling and Verification
Material is specified against IEC 60404-8-7 for cold-rolled grain-oriented electrical steel sheet and strip in the fully processed state, or IEC 60404-8-4 for the non-oriented equivalent, and against ASTM A876/A876M or ASTM A677/A677M respectively. Chinese and Japanese specifications are covered by GB/T 2521.1 and JIS C 2553. Magnetic properties are verified by the Epstein frame method of IEC 60404-2 or the single sheet tester of IEC 60404-3, and the choice of method must be agreed, because single sheet and Epstein results differ measurably. On the shop floor, three habits protect the properties that the certificate describes: keep coils flat and supported, cut laminations with sharp tooling and check burr height at each setup, and never drag a stacked core across a surface, since local plastic deformation raises loss in exactly the region where flux is highest.
Frequently Asked Questions
Q: What does the grade number tell me?
A: The digits after the prefix give the nominal thickness in hundredths of a millimetre and the maximum specific total loss in W/kg at the defined test point, so a 0.27 mm grain-oriented grade quoted at 0.90 W/kg is designated accordingly
Q: Can I compare a non-oriented grade with a grain-oriented grade by loss number?
A: No. Grain-oriented grades are quoted at 1.7 T and 50 Hz and non-oriented grades at 1.5 T and 50 Hz, and the lower flux density flatters the non-oriented figure
Q: Why does burr height matter so much?
A: A burr that penetrates the interlamination coating creates a conducting bridge, allowing circulating currents between laminations, which raises local loss and can develop into a hot spot
Q: What is the difference between the coating types?
A: Coatings are classified in ASTM A976 by chemistry and thickness class; thin inorganic coatings suit wound cores, while heavier coatings resist stress-relief annealing, oil and heat in service
Q: Does the coating affect the stacking factor?
A: Yes. A thicker coating improves interlaminar resistance but reduces the magnetic cross-section, so stacking factors for thin grain-oriented material typically sit between 0.955 and 0.97 depending on thickness and coating class
Q: Which test method should be written into the purchase order?
A: State either the Epstein frame method of IEC 60404-2 or the single sheet tester of IEC 60404-3, because the two methods give different loss values and a result is only comparable with a certificate obtained by the same method

