High Permeability Cut Nanocrystalline C Core

Oct 14, 2025

Leave a message

What Is a Cut Nanocrystalline C Core

A cut nanocrystalline C core is a C-shaped magnetic core produced from iron-based nanocrystalline alloy ribbon. The ribbon is wound into a toroidal or rectangular ring, annealed to develop the fine nanocrystalline grain structure, impregnated, and then cut into two C halves. The mating surfaces are ground flat so that the two halves reassemble into a closed magnetic circuit with a controlled, minimal air gap. The result is a high-permeability core that can be assembled around a winding or bobbin, which makes it the practical choice for transformers and inductors that must be wound on a formed coil.

Manufacturing Route

The process starts with rapid solidification of the molten alloy into a thin ribbon, typically 20 to 30 microns thick. The wound ring is annealed under a controlled magnetic field to grow the nanocrystalline structure and to set the desired B-H loop shape, from high-permeability square loops to linear low-remanence loops. After annealing, the ring is vacuum impregnated with resin so that it can be machined without delaminating, then cut and ground to the final core dimensions. The ground surfaces are the flux-carrying interfaces, so their flatness and surface finish directly affect the assembled core's effective permeability.

Magnetic Properties

High saturation flux density, around 1.2 T, roughly two to three times that of ferrite, allowing smaller cross-sections for the same power.

High permeability, giving low magnetizing current and fewer turns for a given inductance.

Very low core loss at medium and high frequencies, particularly in the 20 to 30 kHz switching range used by many power converters.

Low magnetostriction in optimized grades, which keeps audible noise low.

High Curie temperature, around 570 C, providing stable performance over a wide temperature range.

Nanocrystalline versus Amorphous versus Ferrite and Silicon Steel

Material Saturation (T) Typical Permeability Core Loss at High Frequency Typical Use
Nanocrystalline 1.2 20,000-80,000 Very low High-frequency transformers, chokes, CTs
Amorphous 1.5-1.6 5,000-20,000 Low Distribution transformers, chokes
Ferrite 0.3-0.5 1,000-15,000 Very low but saturates early Low-power high-frequency magnetics
Silicon steel 1.7-2.0 1,000-10,000 High above 1 kHz 50/60 Hz power transformers

Nanocrystalline cores are an upgrade over amorphous cores in saturation flux density, permeability, and loss at high frequency, and they outperform ferrite in power density and temperature stability. Silicon steel remains the economical choice at line frequency, but its loss rises steeply once the operating frequency exceeds about 1 kHz.

Applications

Power transformers in DC-DC converters, welding converters, and inductive heating converters.

High-fidelity audio output transformers where linearity and bandwidth matter.

PFC chokes and filter inductors in power supplies and drives.

Current transformers and measurement cores requiring high accuracy and low phase error.

Isolation transformers in renewable inverters and EV charging systems.

Effect of the Cut and Air Gap

The two C halves are assembled with the ground faces in contact, but a small effective air gap always remains because of surface roughness. This gap reduces the effective permeability of the assembled core compared with the uncut ring, which is often desirable: it flattens the B-H loop, improves linearity, and raises the DC bias capability for inductor duty. For transformer applications the gap must be minimized, so the ground faces are matched pairs and must not be mixed between cores.

Representative Dimensions

The table lists standard cut C-core builds with window width, core height, core width, and core length dimensions; tolerances are shown per the manufacturer's standard.

a (mm) b (mm) c (mm) d (mm) e (mm) f (mm)
9 +/-0.5 10 32.8 15 +/-0.5 28 +/-1 50.8 +/-1.25
11 +/-0.5 13 30 20 +/-0.5 35 +/-1 52 +/-2
11 +/-0.8 13 50 30 +/-0.5 35 +/-1 72 +/-2
13 +/-0.8 15 56 35 +/-0.5 41 +/-1 82 +/-2
16 +/-0.8 20 70 40 +/-0.5 52 +/-1 102 +/-3
19 +/-1 25 83 50 +/-1 63 +/-1 121 +/-3
22 +/-1 35 85 65 +/-1 79 +/-1 129 +/-4
25 +/-1 40 85 85 +/-1.5 90 +/-1 135 +/-4
33 +/-1 40 105 85 +/-1.5 106 +/-1 171 +/-5

Additional sizes are produced to order; the dimensional tolerances and the ground surface quality are agreed with the supplier for the specific application.

Selection Notes

State whether the application is transformer or inductor duty; transformer duty needs matched, gapped-minimized halves, while inductor duty may specify a deliberate gap.

Confirm the operating frequency and the loss budget; this selects the grade and the cross-section.

Check the winding scheme: C cores are wound on a bobbin or form, then the two halves are assembled and banded or clamped.

For current transformers, request the low-remanence grade and the turns/accuracy calculation from the core data.

Frequently Asked Questions

Why is the core cut into two C halves?

Cutting allows the core to be assembled around a pre-wound bobbin, which simplifies winding and insulation compared with a closed toroid. The ground mating faces restore the magnetic circuit when the halves are clamped together.

Does the cut reduce the permeability of the core?

Yes. The effective air gap at the ground faces lowers the assembled permeability below that of the uncut ring. This is controlled by the flatness of the ground surfaces, and for transformer duty the halves are supplied as matched pairs to keep the gap as small and uniform as possible.

Can nanocrystalline C cores replace ferrite cores at high frequency?

In many cases yes. The higher saturation flux density and permeability allow a smaller core for the same power, and the loss is comparable at typical switching frequencies. The material cost is higher, so the decision is based on power density, efficiency, and temperature requirements.

What is the difference between a nanocrystalline and an amorphous C core?

Both are ribbon-based soft magnetic alloys, but nanocrystalline material has a fine crystalline grain structure after annealing, giving higher permeability, higher saturation flux density, and lower loss at high frequency than amorphous material. Nanocrystalline C cores are therefore preferred for the most demanding converter and instrument applications.

How is the core clamped after assembly?

The two halves are normally assembled over the bobbin and secured with steel or stainless bands, or with a clamping fixture that applies controlled pressure to the mating faces. Excessive pressure distorts the core, while insufficient pressure increases the effective gap.

What sizes are available beyond the standard table?

Custom builds are produced to order, with the window, width, and overall length set by the winding and mounting requirements. The minimum practical cross-section is limited by the ribbon width and the handling of thin cores, which the supplier confirms during design review.

Send Inquiry