Application of Silicon Steel: From Motor Cores to Transformer Cores

Oct 20, 2025

Leave a message

What Is Silicon Steel and Why Is It Widely Used?

Silicon steel, also known as electrical steel or lamination steel, is an iron-silicon alloy containing roughly 0.5% to 3.5% silicon by weight. Adding silicon raises electrical resistivity, which sharply reduces eddy-current losses in alternating magnetic fields, while a carefully controlled metallurgical process develops the magnetic texture that gives the material its low core loss and high permeability. Because of these properties, silicon steel is the dominant soft magnetic material in power and electromechanical equipment operating at 50 Hz or 60 Hz, from small fractional-horsepower motors to large generator and transformer cores. The material is supplied in thin sheets, typically 0.23 mm to 0.50 mm thick, which are punched or cut into laminations and stacked to build cores.

Main Application Scenarios of Silicon Steel

Silicon steel applications can be grouped into five major fields, each with different grade requirements and performance priorities.

1. Large-Scale Electromechanical Equipment

Power generation equipment such as wind turbines, thermal generators and hydropower units uses non-oriented silicon steel to manufacture generator stator and rotor cores. The material enables efficient electromagnetic conversion and directly improves power generation efficiency. High-capacity generators typically specify medium to high grade non-oriented steel with tight thickness and flatness tolerances because core losses accumulate across very large active masses.

2. Home Appliances

Motors in home appliances such as washing machines, fans and pumps use non-oriented silicon steel. Although the consumption per unit is small, the huge annual output of household appliances makes this segment one of the largest consumers of electrical steel overall. Air-conditioner compressor motors are a notable example: as energy efficiency regulations tighten, the demand for high-grade non-oriented silicon steel with lower specific core loss has increased significantly.

3. New Energy Vehicles

Traction drive motors of new energy vehicles demand silicon steel with a combination of high magnetic induction, low core loss at high frequency and good mechanical strength. To improve motor performance and power density, stator and rotor cores basically use high-grade non-oriented silicon steel, ensuring efficient operation over the entire speed range. Many EV motors also use thinner laminations (0.25 mm or 0.20 mm) to reduce high-frequency eddy-current losses during high-speed rotation.

4. Industrial Small and Medium-Sized Electromechanical Equipment

Motors for equipment such as rolling mills, cranes, compressors and machine tools require silicon steel cores to provide high torque and reliable power under heavy load. These applications operate in harsh conditions, so the steel must combine stable magnetic properties with good punching quality and mechanical consistency.

5. Transformers, Converters and Similar Static Devices

Grain-oriented silicon steel (CRGO) is mainly used in transformer cores, current transformers and reactors. With the advancement of power grid construction, ultra-high voltage transmission projects and stricter transformer energy efficiency standards, the demand for high-magnetic-induction grain-oriented silicon steel continues to grow. For distribution and power transformers, the grade selection directly determines no-load loss compliance under standards such as GB 20052-2024 and IEC 60076-20.

Key Features That Drive Application Choice

Excellent magnetic properties: high permeability reduces magnetic circuit reluctance, and low iron loss (hysteresis loss plus eddy-current loss) lowers equipment energy consumption and temperature rise.

Strong process adaptability: silicon steel can be rolled into thin sheets below 1 mm; cold-rolled products offer uniform thickness, a flat surface and good punching performance, suitable for mass production of motor and transformer laminations.

High stability: silicon steel shows almost no magnetic aging, so magnetic properties do not decay noticeably after long-term use, which suits equipment designed for decades of continuous operation.

Grain-Oriented vs Non-Oriented: How to Choose

Grain-oriented silicon steel is processed so that the crystal grains are aligned in the rolling direction, giving very low core loss and high permeability when the flux path follows the rolling direction. It is therefore used for transformer cores, where the flux direction is controlled by core geometry. Non-oriented silicon steel has an isotropic magnetic structure and is used where the flux direction rotates, such as motor stators and rotors. As a rule of thumb: if the magnetic circuit is static and directional, choose grain-oriented grades; if it rotates, choose non-oriented grades.

Common Silicon Steel Grades and Typical Properties

The tables below list representative grain-oriented grades and their typical guaranteed values, referenced to the evaluation methods of GB/T 2521.1-2016 and GB/T 2521.2-2016. Core loss is measured at 1.7 T and 50 Hz unless stated otherwise; induction is measured at 800 A/m (B800). Actual certification values follow the mill test certificate of each coil.

Conventional Grain-Oriented Grades (0.23-0.30 mm)

Grade Typical Thickness (mm) Max Core Loss at 1.7 T / 50 Hz (W/kg) Min Induction at B800 (T) Typical Stacking Factor (%)
23Q110 0.23 1.10 1.82 97.2
23Q120 0.23 1.20 1.82 97.2
27Q120 0.27 1.20 1.82 97.5
30G120 0.30 1.20 1.82 98.0

High-Induction and Domain-Refined Grades

Grade Type Max Core Loss at 1.7 T / 50 Hz (W/kg) Min Induction at B800 (T)
23QG095 High induction 0.95 1.88
23QG100 High induction 1.00 1.89
27QG100 High induction 1.00 1.89
23RK085 Domain refined (laser scribed) 0.85 1.88
23RK080 Domain refined (laser scribed) 0.80 1.88
20QG085 High induction, 0.20 mm 0.85 1.86
23RK075 Domain refined (laser scribed) 0.75 1.88

Grades with lower core loss numbers generally cost more but deliver lower no-load losses in the finished transformer, which is why premium distribution transformers specify domain-refined or high-induction grades for Grade 1 energy efficiency.

Application Notes and Common Misconceptions

Do not judge a grade only by thickness: a 0.23 mm conventional grade can have higher loss than a 0.27 mm high-induction grade. Always compare the guaranteed W/kg value at the same induction and frequency.

Handle and cut oriented steel along the rolling direction for transformer cores; cutting against the rolling direction degrades magnetic performance and increases noise.

Stacking factor matters: lower stacking factor means a smaller effective cross-section and higher flux density for the same core volume, which raises core loss and magnetizing current.

Annealing after cutting is recommended for punched transformer laminations to relieve mechanical stress introduced by shearing and punching.

FAQ

What is the difference between silicon steel and ordinary steel?

Silicon steel contains 0.5-3.5% silicon, which increases electrical resistivity and reduces eddy-current losses in alternating fields. It is also processed to develop a favorable magnetic texture, so its core loss is a small fraction of that of ordinary low-carbon steel.

Which silicon steel grade is used for transformer cores?

Transformer cores use grain-oriented silicon steel, typically grades from 0.23 mm to 0.30 mm thickness. Distribution transformers commonly use grades such as 23Q110, 27QG100 or domain-refined grades like 23RK085 depending on the required energy efficiency class.

Why do motor cores use non-oriented silicon steel?

In motors the magnetic flux rotates with the rotor position, so the core material must have uniform magnetic properties in all directions. Non-oriented silicon steel is isotropic and therefore suitable for stator and rotor laminations.

Does using a lower-loss grade always improve motor efficiency?

Not proportionally. Core loss is one part of total motor loss; winding copper loss, friction and windage also matter. Lower-loss steel improves efficiency most in motors with high duty cycles and high operating frequencies, such as compressor and traction motors.

Can silicon steel cores be recycled or reused?

Silicon steel scrap is fully recyclable and is a valuable input for electric steelmaking. Laminations from scrapped transformers and motors are routinely collected; however, cores should never be reused directly in new equipment because cutting and dismantling damage the magnetic properties and insulation coating.

Send Inquiry