Amorphous Cut Core C Transformer Core for Audio Amplifier Transformer

Sep 19, 2025

Leave a message

Amorphous Cut Core C Transformer Core for Audio Amplifier Transformer

An amorphous cut core C transformer core is made from an iron-based amorphous alloy ribbon that is wound into a toroid, impregnated, and then cut into two C-shaped halves. The two halves are ground flat and mated to form a controlled air gap at the joints. This construction is well suited to audio amplifier transformers, where low loss, low noise and stable magnetic behavior are decisive.

Material Properties of Iron-Based Amorphous Alloy

Parameter Typical value
Saturation flux density 1.56 T
Stacking factor > 0.8
Saturation magnetostriction < 30 x 10-6
Initial permeability Much higher than ferrite, in the 10E4 to 10E5 range
Core loss Significantly lower than conventional silicon steel at 1-20 kHz

The high silicon and boron content of the amorphous ribbon suppresses eddy currents, which is why amorphous cores excel in high-frequency and audio-range applications.

Why a Cut C Shape for Audio Transformers

Controlled air gap: the ground joint introduces a defined gap that resists DC saturation from single-ended amplifier bias current.

Low noise: the gap eliminates the objectionable magnetostriction hum of a tightly closed magnetic circuit.

Assembly-friendly: the two halves slip over the bobbin, simplifying winding and repair.

Consistent performance: matched halves keep magnetizing current and inductance repeatable between units.

Performance in Audio Amplifier Duty

Output and power transformers in valve and solid-state amplifiers operate in the 20 Hz-20 kHz band. Amorphous C cores keep core loss low across this range, preserve inductance at high frequencies, and run quieter than conventional EI laminations. The wide frequency response and temperature stability also suit regulated power supplies and class-D amplifier filter inductors.

Comparison with EI Laminations

Item Amorphous C core EI lamination
Core loss at 1 kHz Very low Higher
Air gap control Precise ground joints Butt joints with wider tolerance
Hum and vibration Minimal Noticeable near saturation
Suitability for DC bias Good Moderate

Selection Notes

Match the core cross-section to the required power and the bobbin window to the winding size.

For SE (single-ended) amplifiers, choose a core with a deliberate gap and confirm the inductance at the operating DC bias.

Ask for the B-H curve and loss data at 1 kHz and 10 kHz to compare suppliers objectively.

Verify the stacking factor; a low factor means less effective iron in the same window.

Frequently Asked Questions

Q: Why are amorphous cores good for audio transformers?
They combine high permeability, low core loss and low magnetostriction, which improves frequency response, reduces heat and lowers audible hum.

Q: What is the difference between a cut core and a wound toroid?
A toroid is wound in one piece; a cut core is sliced into two C halves so coils can be wound on bobbins first. Cut cores allow controlled air gaps and easier assembly.

Q: Can amorphous C cores handle DC bias?
Yes, the air gap at the cut joint lets the core accept DC bias without saturating, which is essential for single-ended amplifier output stages.

Q: What is the saturation flux density of amorphous alloy?
Iron-based amorphous alloy reaches about 1.56 T, far higher than ferrite's 0.3-0.5 T, so smaller cores can handle the same power.

Q: Do amorphous cores need special winding?
No special winding is required, but the bobbin should match the C-core window, and the two halves must be clamped evenly to keep the gap uniform.

Q: How are the two C-halves held together, and why does the gap matter?
The halves are banded or clamped evenly so that the mating surfaces sit in uniform contact. The core gap directly controls the magnetizing current and the low-frequency response, so an uneven, contaminated or oversized gap raises excitation current, reduces inductance and adds distortion in audio duty; the clamping pressure must therefore be applied evenly and the cut faces kept clean.

Send Inquiry