Amorphous and Nanocrystalline Wound Toroidal Cores for Transformers, Sensors and Reactors
Oct 23, 2025
Leave a message
What Is a Wound Toroidal Core?
A wound toroidal core is a doughnut-shaped magnetic component produced by winding a thin ribbon of magnetic alloy into a closed ring and then annealing it. Because the magnetic circuit is fully closed with no air gap, toroidal cores offer very high effective permeability, low leakage flux and excellent shielding of external fields. When the ribbon is an iron-based amorphous or nanocrystalline alloy, the core combines these geometric advantages with outstanding magnetic performance at both power frequency and high frequency, which is why amorphous and nanocrystalline wound toroidal cores are widely used in transformers, current sensors and reactors.
Material and Structure
Amorphous state
The core starts as a ribbon produced by rapid solidification, in which the molten alloy is cooled so fast that the atoms do not form a regular crystal lattice. The result is a metallic glass with no crystalline structure. Amorphous ribbons are typically about 20-30 µm thick, much thinner than conventional silicon steel laminations, which naturally reduces eddy-current losses at higher frequencies.
Nanocrystalline state
The amorphous ribbon is then annealed under a controlled temperature cycle and magnetic field. During annealing it crystallizes into an ultra-fine structure with grains of only 10-20 nanometers embedded in an amorphous matrix. This nanocrystalline structure delivers a combination of very high permeability, low coercivity and low core loss that neither pure amorphous nor conventional crystalline materials can match across the same frequency range.
Key Magnetic Characteristics
High permeability: the core is magnetized easily and conducts flux efficiently, which reduces the number of turns needed for a given inductance and improves measurement accuracy.
Low core loss: nanocrystalline structure significantly reduces hysteresis and eddy-current losses, which is critical for high-frequency and high-efficiency designs.
High saturation magnetic flux density: nanocrystalline cores saturate at around 1.2 T, well above ferrite, allowing smaller and lighter devices for the same power rating.
Good thermal stability: performance remains stable over a wide temperature range, with a Curie temperature around 570 °C for nanocrystalline alloys, far above ferrite.
High linearity: the flat hysteresis loop and high permeability make the cores suitable for precision current transformers with low phase error.
Applications
Common-mode chokes
Used to suppress common-mode noise in switching power supplies, inverters and electronic equipment. The high permeability at low frequencies provides strong attenuation, while the low interwinding capacitance of the toroidal geometry maintains performance at high frequencies.
Current transformers
The high accuracy and linearity make nanocrystalline toroidal cores ideal for precise current measurement in metering, protection relays and residual-current devices, including class 0.5 and class 0.2S applications.
Power and high-frequency transformers
Low loss and high saturation flux allow compact transformers for power conversion, including flyback and forward converters operating at 20-100 kHz.
Magnetic amplifiers and saturable reactors
The sharp saturation knee and high squareness ratio are exploited in magnetic amplifiers and controllable saturable reactors for power regulation.
High-frequency inductors
Nanocrystalline toroidal cores are an excellent replacement for ferrite and silicon steel in many medium- and high-frequency inductor applications where size and efficiency matter.
Typical Core Size Options
The following table lists representative wound toroidal core series with their typical power capability. The model designation is CD (winding thickness) x (tape width) x (inner height); the inner height is available in several steps, which changes the window area and therefore the achievable power rating.
| Core Model (mm) | Winding Thickness (mm) | Tape Width (mm) | Inner Height Options (mm) | Typical Power at 50 Hz (VA) | Typical Power at 400 Hz (VA) |
|---|---|---|---|---|---|
| CD6.5 x 12.5 x 8 | 6.5 | 12.5 | 8, 10, 12.5, 16 | 0.05-0.10 | 9.7-20.4 |
| CD10 x 12.5 x 20 | 10 | 12.5 | 20, 25, 32, 40 | 2.4-6.7 | 56.6-112 |
| CD12.5 x 16 x 25 | 12.5 | 16 | 25, 32, 40, 50 | 10.7-25 | 119-221 |
| CD12.5 x 25 x 30 | 12.5 | 25 | 30, 40, 50, 60 | 31.2-63.2 | 222-398 |
| CD16 x 32 x 40 | 16 | 32 | 40, 50, 65, 80 | 89-171 | 470-840 |
| CD20 x 40 x 50 | 20 | 40 | 50, 60, 80, 100 | 199-375 | 813-1,476 |
| CD25 x 50 x 65 | 25 | 50 | 65, 80, 100, 120 | 448-776 | 1,595-2,668 |
| CD32 x 64 x 80 | 32 | 64 | 80, 100, 130, 160 | 1,006-1,843 | 3,197-5,522 |
| CD40 x 80 x 100 | 40 | 80 | 100, 120, 160, 200 | 2,106-3,912 | 6,152-10,737 |
Custom dimensions and performance targets can be produced to meet specific requirements, including gapped cores for energy-storage inductors and cores with a protective coating for winding directly onto the ring.
Selection Notes and Common Misconceptions
Do not confuse amorphous and nanocrystalline materials: amorphous cores are preferred for medium-frequency power transformers up to a few kilohertz, while nanocrystalline cores excel from a few kilohertz up to 100 kHz and above.
Handling matters: nanocrystalline ribbon is magnetostrictive, and mechanical stress changes the loop shape. Cores should be handled with care and, where possible, used with a protective casing or coating.
Temperature behavior: although the Curie temperature is high, the loss of nanocrystalline cores still increases with frequency and flux density; derate the core when operating above 100 kHz.
Saturation limit: if a transformer must withstand high inrush current without saturation, verify that the saturation flux density of the selected core is sufficient for the worst-case condition.
FAQ
What is the difference between an amorphous core and a nanocrystalline core?
An amorphous core is made from a rapidly solidified metallic-glass ribbon with no crystalline structure. A nanocrystalline core is made by annealing that ribbon so that ultra-fine grains of 10-20 nm form. Nanocrystalline cores offer higher permeability and lower core loss at high frequency, while amorphous cores remain a cost-effective choice for many power-frequency and medium-frequency applications.
Why use a toroidal shape instead of E-I laminations?
The toroidal shape has a fully closed magnetic circuit with no air gap, giving higher effective permeability, lower leakage flux and less radiated noise. It also has lower interwinding capacitance in choke applications. The trade-off is more complex winding, since the wire must be threaded through the window.
Can a nanocrystalline toroidal core replace ferrite in a switching power supply?
In many cases yes. Nanocrystalline cores offer higher saturation flux density (about 1.2 T versus 0.4-0.5 T for ferrite), which allows a smaller core for the same energy storage or a larger flux swing for the same core size, reducing the number of turns or the operating frequency requirements.
How do I choose the right core size for a current transformer?
First define the accuracy class, rated primary current and burden. Then check that the core cross-section is large enough to avoid saturation at the maximum fault current, and that the permeability provides the required magnetizing impedance at the working frequency. For metering applications, a nanocrystalline core with high permeability usually achieves class 0.5 or better with fewer turns than silicon steel.
Are these cores suitable for high-temperature environments?
Nanocrystalline cores operate reliably well above 100 °C thanks to a Curie temperature around 570 °C. The practical limit is usually set by the winding insulation and the coating on the core rather than by the magnetic material itself.

