Amorphous vs Nanocrystalline Magnetic Cores: Properties and Selection
Oct 14, 2025
Leave a message
What Are Amorphous and Nanocrystalline Magnetic Cores?
Amorphous and nanocrystalline cores are soft magnetic components produced from metallic-glass ribbon made by ultra-rapid quenching of molten alloy at cooling rates on the order of one million degrees per second. The ribbon, typically 18-30 micrometres thick, is wound into toroidal, C-shape or block geometries and annealed in a magnetic field to develop the final magnetic properties. Their defining advantages over ferrite and silicon steel are very high permeability combined with low core loss, which makes them the preferred material for precision current transformers, common-mode chokes and high-frequency power conversion.
Material Structure: Amorphous vs Nanocrystalline
Amorphous cores
In an amorphous core the atoms are arranged randomly rather than in a crystal lattice. Iron-based amorphous alloys (Fe-Si-B with small additions) reach a saturation flux density of about 1.5-1.6 T, offer roughly three times the electrical resistivity of silicon steel, and show extremely low loss at power and medium frequencies. The random structure also keeps hysteresis loss low.
Nanocrystalline cores
Nanocrystalline cores start from the same amorphous ribbon and are then annealed so that nanoscale iron grains of 10-20 nm precipitate inside the amorphous matrix, typically in Fe-Si-B-Nb-Cu alloys. The result combines very high initial permeability (typically tens of thousands and up to about 100,000) with saturation flux density around 1.2-1.25 T and core losses that stay low up to roughly 100 kHz.
Property Comparison
| Material | Initial permeability | Saturation flux density | Typical core loss | Usable frequency | Typical applications |
|---|---|---|---|---|---|
| Fe-based amorphous | 3,000-10,000 | About 1.56 T | Very low at 50 Hz-10 kHz | Power to medium frequency | Distribution transformer cores, chokes, CTs |
| Nanocrystalline | 40,000-120,000 | About 1.2 T | Very low up to about 100 kHz | 10-100 kHz | Common-mode chokes, precision CTs, HF transformers |
| Mn-Zn ferrite | 2,000-15,000 | 0.3-0.5 T | Low at high frequency | 100 kHz-1 MHz | SMPS transformers, inductors |
| Grain-oriented silicon steel | 2,000-10,000 (effective) | About 2.0 T | Lowest at 50/60 Hz | Power frequency | Power and distribution transformers |
Values are typical ranges from published material data; guaranteed figures are given in the manufacturer test certificate.
Why Low Loss and High Permeability Matter
Low hysteresis loss comes from the thin ribbon and optimized anisotropy after field annealing; low eddy-current loss comes from high resistivity and the thin lamination thickness. High permeability means fewer turns are needed for a given inductance, which shrinks the core and cuts copper loss. The combination lets designers build smaller, cooler, more efficient magnetic components than with ferrite or silicon steel in the same duty.
Application Guide
Precision current transformers for metering, protection and control, where high permeability and tight material consistency deliver accuracy classes such as 0.1 and 0.2S.
Common-mode and normal-mode chokes for electromagnetic interference (EMI) filtering in power supplies, drives and vehicle chargers.
High-frequency power transformers and inductors in switch-mode power supplies, solar inverters, UPS and induction heating equipment.
Saturable reactors and magnetic switches.
Wireless charging systems and magnetic sensors.
Selection Considerations
Choose by operating frequency, required permeability, flux density swing and any DC bias. Nanocrystalline suits precision and high-frequency duties; amorphous suits power-frequency and medium-frequency tasks where higher saturation is useful. Toroidal cores give the highest effective permeability and lowest stray field; cut C-cores allow a controlled air gap for energy storage or DC bias. Specify dimensions, target inductance or turns, frequency, current, temperature range and coating when ordering.
Frequently Asked Questions
What is the difference between amorphous and nanocrystalline cores?
Amorphous cores have a random, non-crystalline atomic structure with saturation around 1.5-1.6 T and moderate permeability; nanocrystalline cores contain nanoscale crystallites in an amorphous matrix, giving much higher permeability (tens of thousands to about 100,000) and very low loss up to about 100 kHz, at a slightly lower saturation of about 1.2 T.
Why are these cores used in current transformers?
High permeability minimizes the magnetizing current and ratio error, so the transformer can maintain its accuracy class over a wide current range with a compact core.
Can nanocrystalline cores tolerate DC bias?
Only up to a small magnetizing level; because saturation flux density is about 1.2 T, significant DC bias requires an air gap or a larger core. State the DC component when ordering.
What is the operating temperature range?
Typical Fe-based amorphous and nanocrystalline cores operate from about -55 C to +130 C without significant change in magnetic properties.
Are these cores used in 50/60 Hz distribution transformers?
Amorphous cores are, because their ultra-low no-load loss cuts idle energy consumption; nanocrystalline is used mainly where high frequency or precision is required rather than at power frequency and high power.
How should I specify a core?
Provide outer and inner diameter and height for toroids, or strip width and build for C-cores, plus frequency, inductance or turns, flux density, DC bias, temperature range and coating requirement.

