Fe-Based 1K107 Magnetic Ring Cores for Electronic Transformers and Sensors

Oct 24, 2025

Leave a message

The Ring Core Concept

A magnetic ring core is a toroidal component wound from a continuous ribbon of soft magnetic alloy into a closed ring. Because the magnetic circuit is closed and continuous, the flux is guided entirely inside the material, giving high inductance per turn, low magnetic leakage and very low sensitivity to external fields.

The 1K107 ring core described here is made from iron-based nanocrystalline alloy, which combines the high saturation of iron-based materials with the very low losses of nanocrystalline structures. Ring cores of this type are the standard solution for precision current transformers, common-mode chokes and high-frequency transformers in electronic equipment.

Material Properties of 1K107

The alloy is produced by rapid solidification into a ribbon of 18 to 22 microns thickness, followed by annealing that forms a nanocrystalline structure. The resulting material has an initial permeability of 60,000 to 80,000, a saturation flux density of about 1.25 T, a coercivity below 1 A/m and a Curie temperature of about 570 degrees Celsius.

These properties translate directly into component performance: a current transformer wound on a 1K107 ring needs far fewer turns for a given accuracy class, and a common-mode choke achieves high impedance in a small volume with negligible temperature drift.

Manufacturing Route

The manufacturing process starts with slitting the annealed ribbon to the required width, followed by winding the strip onto a mandrel to form the ring. The wound ring is then annealed in a magnetic field to develop the highest possible permeability, and the surface is coated with an insulating layer.

Depending on the application, the ring can be supplied bare, in a protective plastic case, or with a ground air gap for DC-biased applications. Each core is tested for permeability and core loss on a sample basis, and the dimensional tolerances are verified against the drawing.

Typical Electronic Applications

The main applications are precision current transformers for energy metering and protection relays, common-mode chokes for electromagnetic compatibility filtering, gate drive and pulse transformers for power electronics, and high-frequency transformers for DC-DC converters.

In metering applications, the high permeability of the core reduces the excitation current, which improves the ratio and phase accuracy of the current transformer at low primary currents. In EMC filtering, the high impedance of the choke suppresses common-mode noise over a wide frequency range.

Selection and Ordering Data

When ordering a 1K107 ring core, the customer specifies the outside diameter, inside diameter and height of the ring, the target permeability class, and whether the core needs a case or an air gap. The supplier confirms the effective cross-sectional area and the magnetic path length, which the designer needs to calculate the number of turns.

For volume production, the permeability and loss values are controlled within the declared class limits, and a test certificate can be issued for each batch.

Frequently Asked Questions

Q: What is the difference between a ring core and a toroidal core?
A: The two terms describe the same geometry. A ring core is a toroidal component with a circular cross-section and a round window, wound from continuous ribbon. Some suppliers use ring for small precision cores and toroidal for larger power cores, but the magnetic principle is identical.

Q: Why is the leakage of a ring core so low?
A: The closed ring guides the flux entirely inside the material, and the winding is distributed evenly around the whole circumference. Because there is no air gap and no free space between core and winding, the leakage inductance and the radiated field are minimized.

Q: Can the ring core be used with DC bias?
A: The standard closed ring has no air gap, so it saturates quickly under DC current. For DC-biased applications such as filter inductors, the ring can be cut to introduce a controlled air gap, or a material with lower permeability can be selected to reduce the flux density at the working current.

Q: What accuracy can be achieved in current transformers?
A: With a high-permeability 1K107 ring and careful winding, current transformers can meet accuracy classes 0.1 and 0.2 for metering applications. The excitation current of the core must be kept low, which is exactly what the high permeability of the material provides.

Q: Are the cores supplied with test data?
A: Yes. Each production batch is tested for permeability, core loss and dimensions. A certificate can be issued with the batch number, the measured values and the declared class limits of the material.

Send Inquiry