FAQ About Hot-dip Galvanized Sheet(二)
Feb 21, 2024
Leave a message
11. How long is the maximum allowed storage time for finished products in the warehouse? Why?
Answer: It is allowed to be stored for three months to avoid oxidation caused by long-term storage.
12. What is the length tolerance of galvanized steel sheet?
Answer: The length tolerance is not allowed to have a negative value, and the maximum is not allowed to exceed +6mm.
13. What is big spangle? What is a small spangle?
Answer: Large spangles are normal spangles. Large spangles can be produced according to the normal production process. The diameter of the crystal nucleus is not less than 0.2mm; the diameter of the crystal nucleus is less than 0.2mm, which is called small spangles. Generally, this kind of spangles cannot be used. Recognizable by naked eyes.
14. What is the protection principle of the hot-dip galvanized layer?
Answer: Because zinc can form a film with good corrosion resistance on the surface in a corrosive environment. It not only protects the zinc layer itself, but also protects the steel base.
15. What is the principle of passivation of hot-dip galvanized sheet?
Answer: Chromate passivation treatment of galvanized sheet can form a passivation film, and its chemical reaction formula is as follows: Zn+H2GrO4-ZnGrO2=H2
The trivalent chromium in the solution passivation group is insoluble in water, chemically inactive, and acts as a skeleton, while the hexavalent chromium in it is easily soluble in water, and can play a role in repassivation when the passivation film is scratched. Has the healing effect of a passive film. Therefore, within a certain limit, the passivation film can prevent steam or humid air from directly corroding the galvanized sheet, and the zinc layer plays a protective role.
16. What are the methods for testing the corrosion resistance of hot-dip galvanized sheets?
Answer: There are three methods for testing the corrosion resistance of hot-dip galvanized sheets: salt spray test; humidity test; corrosion test.
17. Why is anti-rust treatment required for hot-dip galvanized products?
Answer: When the hot-dip galvanized sheet is in humid air, especially when the air contains acidic substances such as SiO2, CO2, NO2 and NO, the surface of the galvanized layer will soon form loose white rust. The main components of white rust are ZnO and Zn(OH)2. This kind of white rust not only affects the appearance, but also brings great difficulties to future use.
18. What are the causes of white rust?
Answer: The causes of white rust are: hot-dip galvanizing is put together with other corrosive media such as acid, alkali, and salt; the passivation film or anti-film is destroyed; the passivation or oiling effect is not good; the storage warehouse is not well ventilated, Moisture; galvanized sheets are watered during transportation; transported at low temperatures and stored at high temperatures, forming condensation.
19. How to calculate the coating thickness?
Answer: The coating thickness formula is: Dz=Gz (Sz*dz) where: Dz--coating thickness mm, Gz--coating weight g per square meter, Sz--coating area mm2, dz--proportion of zinc , the above formula can be simplified as: Dz=0.000139Gz
20. What are the causes of zinc particles?
Answer: The problem of the original plate is mainly the cleanliness of the original plate and the content of iron powder in the original plate; the temperature of the zinc liquid is too high, which makes the bottom dross float; the content of Al is too high, which affects the solubility of iron.
21. What is the significance of hot-dip galvanized sheet skinning?
Answer: With the continuous expansion of the use of hot-dip galvanized sheets, in the modern continuous hot-dip galvanizing line for strip steel, the following goals can be achieved by skinning the strip steel:
① Improve the straightness and flatness of the thin plate, and at the same time flatten the zinc particles on the surface to make the surface of the strip steel smooth, which is especially beneficial for deep drawing and other occasions with high precision in use in the future;
②The skinning roller used has been pre-shot blasted, so the surface of the skinned plate has a certain roughness. It can improve the adhesion of the coating and store a certain amount of grease, which is beneficial to the lubrication of the die during deep drawing;
③ For the galvanized plate that will be painted later, although the surface is controlled into small spangles, the small spangles can still be exposed through the paint layer. Therefore, for some galvanized sheets with high requirements, the surface of small spangles needs to be light-finished. This will give the galvanized sheet a more uniform silver-white appearance;
④Through skinning, the lower yield point can be reduced, so that the yield platform disappears or is not obvious, which can prevent the slip line from appearing in the subsequent stretching or deep drawing process, and improve the possibility of deep drawing.
Galvanized Carbon Steel Sheet


