What is the Process of Galvanizing Steel?
Feb 19, 2024
Leave a message
Galvanizing is the process of applying a protective zinc coating to steel to prevent corrosion. The most common industrial method is continuous hot-dip galvanizing, in which steel strip or fabricated parts are cleaned, fluxed and immersed in molten zinc so that a metallurgically bonded zinc layer forms on the surface. Because zinc corrodes preferentially to steel, the coating protects the base metal both as a barrier and as a sacrificial anode. This article explains the process step by step, the coating designations used in international trade, and the factors that determine service life.
Why Galvanize Steel?
Bare steel rusts when moisture and oxygen reach its surface. A zinc coating interrupts this process in two ways:
Barrier protection: the dense zinc layer physically separates the steel from the atmosphere.
Sacrificial (cathodic) protection: at scratches and cut edges where steel is exposed, zinc corrodes in preference to steel, so the exposed area remains protected as long as zinc is present nearby.
This dual mechanism makes galvanizing one of the most cost-effective corrosion protection systems for structural steel, with typical maintenance-free service lives measured in decades in most atmospheric environments.
The Hot-Dip Galvanizing Process Step by Step
1. Surface Preparation
The quality of the zinc coating depends almost entirely on surface cleanliness. The steel first passes through an alkaline degreasing bath to remove oils, greases and drawing compounds, then through pickling in diluted hydrochloric or sulfuric acid to remove mill scale and rust. After each chemical stage the strip is rinsed with water.
2. Fluxing
Before immersion, the steel is coated with a flux, typically a zinc ammonium chloride solution. The flux prevents oxidation of the cleaned surface between pickling and dipping and promotes wetting of the steel by molten zinc.
3. Hot-Dip Coating
The prepared steel is immersed in a bath of molten zinc maintained at approximately 450 °C (about 840 °F). Iron and zinc react at the interface to form a series of zinc-iron intermetallic alloy layers, overlaid by a layer of relatively pure zinc. This metallurgical bond is what distinguishes hot-dip galvanizing from paint or other surface coatings.
4. Withdrawal and Control of Coating Weight
As the strip leaves the bath, gas knives (air or nitrogen wipers) strip excess zinc from the surface and control the final coating thickness precisely. The coating is then cooled and, for sheet products, may receive a light pass or other finishing treatment.
5. Inspection
Coating weight is verified by weighing a specimen before and after dissolving the zinc layer (the triple-spot test), and coating adhesion is checked by bending tests. Continuous production lines monitor coating thickness online with gauges.
Coating Weights and Designations per ASTM A653/A653M
Galvanized sheet products are described by base metal grade and coating designation. ASTM A653/A653M, the standard specification for steel sheet, zinc-coated by the hot-dip process, defines coating designations that state the minimum total coating weight on both surfaces.
G-60: minimum total coating weight of 0.60 oz/ft² (about 183 g/m²) both sides combined, typically corresponding to a coating thickness of about 0.40 mil (10 µm) per side.
G-90: minimum total coating weight of 0.90 oz/ft² (about 275 g/m²), roughly 0.60 mil (15 µm) per side.
G-110, G-140, G-165 and G-185 designate progressively heavier coatings for more corrosive environments.
In metric terms, common designations are Z180, Z275 and Z350, where the number is the total coating mass in g/m². The same physical coating can be ordered under either system; ASTM A653/A653M is the governing standard for inch-pound designations, while ISO 1461 covers hot-dip galvanized coatings on fabricated iron and steel articles, and GB/T 2518 governs continuous hot-dip zinc-coated steel sheet in China.
Other Galvanizing Methods
Besides continuous hot-dip coating of sheet and strip, several related processes are used:
Batch (general) hot-dip galvanizing per ISO 1461: fabricated structures such as transmission towers and handrails are cleaned, fluxed and dipped in molten zinc.
Electrogalvanizing: zinc is deposited electrolytically, giving a thinner, smoother coating used mainly for automotive body panels where paint adhesion is important.
Zinc thermal spraying: molten or powdered zinc is sprayed onto large structures that cannot be dipped.
Sherardizing: small parts are tumbled with zinc dust at elevated temperature to form a diffusion coating.
Service Life and Corrosion Protection
The service life of a galvanized coating depends on coating thickness and the corrosivity of the environment. As a practical rule, zinc corrodes at roughly 1 µm per year in mild rural atmospheres, and faster in industrial or marine environments. A G-90 coating therefore provides decades of protection in most inland applications. Corrosion rate data are published in ISO 9223 and related standards, which classify atmospheric corrosivity and allow engineers to select the coating weight for the design life.
Common Applications
Galvanized steel is used wherever long life and low maintenance are required: building frames, roof and wall sheeting, transmission towers and utility poles, highway guardrails, agricultural buildings, HVAC ducting, electrical enclosures and transformer tanks. In the electrical industry, transformer oil tanks are frequently fabricated from galvanized or otherwise corrosion-protected steel to survive outdoor service.
Frequently Asked Questions
Q: What is the difference between G-60 and G-90 coating?
Both are defined in ASTM A653/A653M as minimum total coating weight on both surfaces. G-90 (0.90 oz/ft2, about 275 g/m2) is roughly 50% heavier than G-60 (0.60 oz/ft2, about 183 g/m2) and gives proportionally longer service life in the same environment.
Q: Does galvanizing protect cut edges and scratches?
Yes. Because zinc is anodic to steel, exposed steel at cut edges and scratches is protected sacrificially by the surrounding zinc coating, giving the coating a self-healing characteristic that paint systems do not have.
Q: Why is the steel cleaned before dipping?
Molten zinc does not wet oily or scaled steel. Degreasing, pickling and fluxing produce a chemically clean, oxide-free surface so the zinc can react with the iron and form a continuous metallurgical bond.
Q: What temperature is the molten zinc bath?
Continuous hot-dip lines operate at about 450 degrees C (about 840 degrees F). Higher temperatures accelerate growth of brittle zinc-iron alloy layers, so the bath is held within a narrow window.
Q: Can galvanized steel be painted?
Yes, after appropriate preparation such as cleaning plus a suitable primer. The duplex system of galvanizing plus paint gives much longer life than either coating alone and is widely used on high-visibility structures.
Q: How do I select the right zinc coating weight?
Match the coating weight to the corrosivity category of the site (ISO 9223) and the required design life. G-60 or G-90 covers most indoor and rural work, while G-140 and G-185 are specified for marine and industrial atmospheres.

