UI Lamination Core: Design, Materials and Applications

Oct 10, 2025

Leave a message

How a UI Lamination Core Is Constructed

A UI lamination core is a shell-type magnetic core for single-phase transformers, assembled from U-shaped and I-shaped laminations that are interleaved in alternating layers. The U laminations form the main flux path around the winding window, and the I laminations close the magnetic circuit at the open ends. Because the flux path is short and straight, the reluctance of the core is low, which reduces the magnetising current and improves the efficiency of small transformers. The interleaved joint also distributes the air gaps between layers, which lowers the effective gap losses compared with a butt joint.

Materials: CRGO and CRNGO

UI cores are made from cold-rolled silicon steel in either grain-oriented or non-oriented form. Cold-rolled grain-oriented (CRGO) grades, such as M3, M4, M5 and M6, are used where the flux direction is fixed and minimum loss is required; they are supplied in thicknesses from 0.23 mm to 0.35 mm. Cold-rolled non-oriented (CRNGO) grades, such as the 35W250 to 35W400 series at 0.35 mm and the 50W250 to 50W1300 series at 0.50 mm, are used where cost or multi-directional flux matters, for example in some control and appliance transformers. The table below summarises the typical material selection.

Material Group Grades Thickness (mm) Coating
CRGO M3, M4, M5, M6 0.23 to 0.35 T2 inorganic
CRNGO 35W250, 35W300, 35W400 0.35 T4 semi-organic
CRNGO 50W250 to 50W1300 0.50 T4 semi-organic

Advantages over EI Cores

The UI configuration allows a slimmer, more compact transformer than an EI core of equivalent rating, because the windings are distributed over the two legs and the core height is reduced. The short, straight magnetic path lowers reluctance and stray loss, and the shell-type structure gives good electromagnetic shielding of the winding. In addition, the U and I laminations are simple shapes that can be punched with minimal scrap, which is an advantage in large production runs of control transformers, ballasts and power supplies.

Applications

UI lamination cores are used in control transformers, auto transformers, isolation transformers, small power transformers, ballasts, reactors, inductors, inverter power supplies, voltage stabilisers and uninterruptible power supplies. They are also found in battery chargers and appliance power circuits where a compact single-phase magnetic component is required. The core is usually wound with a bobbin-mounted coil and then clamped or welded to hold the laminations in compression, which keeps the audible noise low.

Dimensional Range

Standard UI cores are available from UI-16 up to UI-80, with larger or non-standard sizes produced to customer drawings. The dimensions below are the common standard values in millimetres; the final drawing governs the delivered part.

Type a b c d e Holes Aperture (mm)
UI-16 48 16 16 48 16 4 4.5
UI-20 60 20 20 60 20 4 6
UI-25 75 25 25 75 25 4 8
UI-35 105 35 35 105 35 4 10
UI-50 150 50 50 150 50 4 8 or 11
UI-80 240 80 80 240 80 4 14

Manufacturing Options

UI cores can be supplied annealed or unannealed depending on the customer requirement. Annealing relieves the cutting stress and restores the magnetic properties of the steel, which matters when the loss target is tight; unannealed cores are lower cost and acceptable for less demanding applications. Mounting holes, apertures and special leg lengths are customised to the drawing, and the interlaminar coating is selected from the inorganic T2 type for CRGO or the semi-organic T4 type for CRNGO material.

FAQ

What is the difference between UI and EI cores?

An EI core uses E-shaped and I-shaped laminations with the winding on the central leg, while a UI core uses U-shaped and I-shaped laminations with the winding split across two legs. The UI design is slimmer and offers a shorter magnetic path.

Which material is best for a UI transformer core?

CRGO grades M3 to M6 are preferred when minimum loss and high efficiency are required, for example in isolation and control transformers; CRNGO grades are chosen for cost-sensitive applications at 50 or 60 Hz.

Why are UI cores annealed?

Cutting and punching introduce mechanical stress that degrades the magnetic properties. A stress-relief anneal restores low core loss and high permeability, and is essential when the design targets tight loss limits.

What coatings are used on UI laminations?

CRGO material typically uses T2 inorganic coating, which withstands the annealing temperature, while CRNGO uses T4 semi-organic coating. The coating provides interlaminar insulation between stacked sheets.

Can UI cores be customised?

Yes. Leg dimensions, stack height, mounting holes, apertures and coating can all be adapted to the customer drawing, and non-standard sizes are produced on request.

Send Inquiry