Galvanised Steel Coil vs Cold Rolled Steel Coil: How to Choose

Feb 01, 2024

Leave a message

Two Processes, Two Purposes

Galvanised steel coil and cold-rolled steel coil are both carbon steel products made from hot-rolled substrate, but they answer different questions. Galvanising answers the question of corrosion protection, while cold rolling answers the question of dimensional accuracy and surface finish. They are not competing materials, because cold-rolled strip is very often the substrate that is later galvanised.

The practical choice is therefore simple. If the finished part will be exposed to weather, humidity or a mildly corrosive environment, the coating matters most. If the part will be stamped, formed, painted or machined to a tight tolerance indoors, the gauge and the surface matter most. Many projects need both, in which case the correct answer is a galvanised coil built on a cold-rolled substrate.

How Hot-Dip Galvanised Coil Is Made

In continuous hot-dip galvanising, cleaned and annealed strip passes through a bath of molten zinc at around 450 °C. A metallurgically bonded zinc-iron alloy layer forms at the interface, and a nearly pure zinc layer solidifies on top of it. Coating mass is stated in grams per square metre over both surfaces, from Z60 to Z275 in EN 10346, or in ounces per square foot from G30 to G90 in ASTM A653. After the bath the coating can be left with a normal spangle, cooled to give a minimised spangle, or skin passed to give a zero-spangle surface.

Why zinc protects steel. Zinc is electrochemically more active than iron, so in a corrosive electrolyte it corrodes preferentially and supplies cathodic protection to the steel wherever the coating is cut or damaged. Even at a sheared edge or a deep scratch, the surrounding zinc continues to protect the exposed steel. Over time the zinc oxidises into a stable patina that slows further attack, which is the dull grey appearance of weathered galvanising.

How Cold-Rolled Steel Coil Is Made

Cold rolling takes hot-rolled strip and reduces its thickness below the recrystallisation temperature, normally at ambient temperature, between successive sets of rolls, then anneals and skin passes it to finish. The consequences are:

a tight thickness tolerance and a much smoother surface than hot-rolled strip;

higher strength from work hardening, and a uniform, formable structure after annealing;

a clean, flat substrate for painting, lacquering, organic coating or later galvanising;

consistent mechanical properties that allow high-speed stamping and roll forming.

Because the surface is bare, cold-rolled coil carries no corrosion protection of its own. Indoors, in oiled condition and inside painted assemblies, that is normally acceptable. Outdoors it is not, which is why the same substrate is so often galvanised or organically coated before use.

Galvanised and Cold-Rolled Coil Compared

Aspect Galvanised coil Cold-rolled coil
Primary purpose Corrosion protection Forming and dimensional accuracy
Key feature Zinc coating, commonly Z60 to Z275 Precise gauge, smooth clean surface
Protection mechanism Barrier layer plus sacrificial anode None, unless painted or oiled
Typical supply thickness About 0.2 mm to 4.0 mm About 0.2 mm to 3.0 mm
Typical use Roofing, cladding, purlins, outdoor structures, automotive bodies Appliances, panels, truck and car inner parts, furniture, tubes
Welding Possible, but zinc fumes must be extracted Straightforward
High-temperature service Not suitable above roughly 200 °C Limited only by the base steel grade

The two products also differ in how they are bought. Galvanised coil is ordered by coating mass plus gauge, and the certificate must state the coating designation and the passivation treatment. Cold-rolled coil is ordered by grade, gauge tolerance and surface finish, with the mechanical properties and the temper rolled condition named on the certificate.

Limitations to Design Around

Temperature: zinc melts at about 419 °C, and above roughly 200 °C the coating creeps and degrades quickly, so galvanised coil is unsuitable for hot service.

Mechanical damage: a deep scratch that removes zinc locally exposes the steel. The surrounding coating still gives some cathodic protection, but severe damage should be repaired with zinc-rich paint.

Welding: zinc fumes are toxic. Weld in ventilated areas and strip the coating from weld zones where appearance or paint adhesion matters.

Forming: the coating can flake or powder when the bend radius is too tight, so forming radii have to respect the coating thickness and the base steel ductility.

Storage: white rust develops on stacked, damp galvanised sheets where air cannot circulate, so coils and packs need dry, ventilated storage and prompt use.

Fire protection. Both main approaches used for steel buildings can be applied to galvanised members. Cement-bonded dense or lightweight protection suits exposed structural elements, while intumescent coatings foam on heating and form an insulating char that slows heat transfer into the steel. Porous fireproofing can trap moisture against the zinc and accelerate corrosion, and it also hides the surface from inspection, so a compatible primer system and inspection access should be built in at the design stage.

Frequently Asked Questions

Q: Is galvanised coil simply cold-rolled coil with a coating?
In many cases yes. Cold-rolled strip is a common substrate for hot-dip galvanising, which is why the two products are related rather than competing.

Q: Which one should I choose for outdoor structures?
Galvanised coil, because the zinc layer provides both a barrier and sacrificial protection at cut edges and scratches. Bare cold-rolled steel would need painting for the same service.

Q: How is the zinc coating specified?
By coating mass per unit area. EN 10346 uses Z60 to Z275 in grams per square metre over both surfaces, and ASTM A653 uses G30 to G90 in ounces per square foot.

Q: Can galvanised steel be welded?
Yes, but the zinc fume is toxic, so welding needs good extraction or respiratory protection, and the coating is usually removed from the weld zone to protect appearance.

Q: Why does the zinc layer protect a cut edge?
Because zinc is electrochemically more active than iron. It dissolves preferentially and keeps the exposed steel cathodic, even where the coating has been sheared or scratched.

Q: What temperature limit applies to galvanised coil?
Continuous service above about 200 °C accelerates coating degradation, and zinc melts at roughly 419 °C, so hot applications require uncoated or heat-resistant steel.

Send Inquiry