EI Lamination Core Sets for Transformers and Chokes

Sep 23, 2025

Leave a message

Geometry of E-I and E-E Lamination Sets

An EI core is a laminated magnetic circuit assembled from E shaped and I shaped stampings. In the classic arrangement an E lamination is closed by an I lamination placed across its leg ends, so the magnetic path passes through the centre leg and returns through the two outer legs. Two E laminations can also be placed leg end to leg end so that the window of one completes the other, which is the basis of the E-E stack used in some transformer designs.

The feature that made the family so widely used is the open coil side. With E-I construction the coil is wound on the centre leg before the I laminations are fitted, so the winding operation never has to pass wire through a closed window. That lowers winding cost for small and medium transformers and chokes and suits a simple moulded bobbin.

Why Scrapless Nesting Matters

The scrapless pattern removes the waste of separate E and I punches. The electrical steel left between two adjacent E laminations, placed leg end to leg end, becomes exactly the material for the I laminations that close the magnetic path. Utilisation of the strip approaches the theoretical maximum, which matters because on grain-oriented material the steel itself dominates the cost of the finished core.

The layout also makes the magnetic path predictable. Because every lamination comes from a known orientation in the strip, the direction of magnetisation is known in advance, so loss and permeability can be estimated from the strip data rather than discovered after assembly. On a hand-laid punch pattern this control is easily lost, and the resulting loss scatter between batches becomes difficult to explain to a design engineer.

Selecting the Core Material

The same EI profile is produced in three material families, and the choice is driven by frequency, flux density and loss budget rather than by the shape itself.

Core material Typical thickness Loss reference Typical EI application
Grain-oriented electrical steel 0.23 to 0.30 mm Specific total loss at 1.7 T, 50 Hz Mains transformers where no-load loss dominates
Non-oriented electrical steel 0.35 to 0.50 mm Specific total loss at 1.5 T, 50 Hz General 50 and 60 Hz transformers, chokes and reactors
Manganese-zinc ferrite Solid, not laminated Core loss at the stated frequency and flux density High-frequency transformers and inductors

Ferrite EI cores are chosen where the switching frequency is far above mains, because their high resistivity suppresses the eddy currents that would make laminated steel unusable. Their saturation flux density is much lower than that of silicon steel, which is the trade-off accepted for a large reduction in loss at high frequency.

Air Gap, Stacking Factor and Assembly

Interleaving is the standard assembly method. Laminations are stacked in two or more groups with the joint position alternated, which distributes the air gap around the magnetic path instead of concentrating it in one plane. Alternating the joints raises effective permeability and lowers loss compared with butt stacking, where all I laminations sit on one side and the gap is deliberately large. Butt stacking with a defined gap is nevertheless used for inductors and chokes that must carry DC bias without saturating, because the stored energy depends on that gap.

Stacking factor for well flattened laminations is typically 0.93 to 0.97, so the effective magnetic cross-section is smaller than the physical core area and must be used in the design calculation. Burr height, coating thickness and lamination flatness all reduce the factor, while excess clamping pressure can cut through the coating and create inter-laminar shorts.

Electrical Performance and Safety Notes

Because the coil sides are open, EI cores give generous room for lead-out wires and terminals, and heat escapes from the coil more easily than in a closed-window design. The same openness means the structure must be clamped or banded so that the stack does not loosen under magnetostrictive vibration, which would otherwise show up as audible noise and eventually as abrasion of the insulation coating.

For safety-critical mains transformers, creepage and clearance distances and insulation coordination are set by IEC 61558-1, and the core must be earthed or the design double insulated accordingly. Where the core is clamped by a metal band that passes near the winding, the creepage path along that band is part of the insulation design and cannot be treated as a mechanical detail.

Frequently Asked Questions

Q: What does the designation EI mean?
It describes a lamination set made of E shaped and I shaped pieces. The E carries the wound centre leg and the two outer legs, and the I closes the magnetic path across the leg ends.

Q: What is scrapless EI nesting?
A punching layout in which the I laminations are cut from the material remaining between two adjacent E laminations, so almost no electrical steel is lost as scrap.

Q: Should an EI core use grain-oriented or non-oriented steel?
Grain-oriented steel suits mains transformers where the flux follows the rolling direction and no-load loss matters. Non-oriented steel is less expensive and is used for general chokes and small 50 and 60 Hz transformers.

Q: Why are EI cores interleaved during assembly?
Interleaving alternates the position of the joints, which spreads the air gap around the path, raises effective permeability and reduces both no-load loss and noise compared with butt stacking.

Q: What stacking factor should be assumed in design?
Between about 0.93 and 0.97 depending on lamination flatness, burr height and coating thickness. The remainder is insulation and air, and the magnetic cross-section must be reduced accordingly.

Q: Can ferrite EI cores replace steel laminations?
Only at high frequency. Ferrite has much higher resistivity and lower loss above roughly 20 kHz, but its saturation flux density is far lower than silicon steel, so it cannot replace laminations in mains-frequency power transformers.

Send Inquiry