High-Flux Amorphous C-Shape Core for Electronics: Design and Customization
Oct 14, 2025
Leave a message
What Is an Amorphous C-Shape Core?
An amorphous C-core is a magnetic core formed from rapidly quenched Fe-based amorphous ribbon, wound into a toroid and then cut into two C halves. The cut faces form precisely controlled air gaps that set the effective permeability and allow the core to store magnetic energy - a key requirement for inductors and flyback transformers. C-cores are easy to wind: the coil is made on a bobbin or former and the two halves are assembled around it, so large conductors and many turns are practical without threading through a toroid.
Material: High-Flux Amorphous Alloy
The ribbon is produced by quenching molten alloy on a cooling wheel at speeds exceeding one thousand metres per second of surface velocity, which prevents the atoms from forming a crystal lattice. The primary elements are iron, silicon and boron, chosen to optimize magnetic performance while keeping losses low. The non-crystalline structure gives high electrical resistivity and low hysteresis loss. Fe-based amorphous alloys reach a saturation flux density of about 1.5-1.6 T - far above ferrite - while keeping core loss low at medium frequencies, which is why they are described as high-flux for power electronics duty.
Why Choose a C-Shape Geometry
Easy winding: coils are wound separately on formers and slid over the core legs, unlike toroids which must be wound through the hole.
Controlled air gap: the gap length sets the effective permeability and prevents saturation under DC bias, making the core suitable for energy-storage inductors.
Low core loss with high flux: amorphous material keeps losses low in the 1-20 kHz range while delivering much higher flux density than ferrite for a given size.
Simple mounting: the two halves are clamped with steel banding or brackets, giving a mechanically robust assembly.
Customization Options
Dimensions: strip width, build height, overall cross-section and leg spacing to fit the winding window.
Gap length and target effective permeability for the required inductance and DC bias margin.
Coating and boxing for winding insulation and mechanical protection.
Annealing conditions tailored to the operating frequency and flux density.
Mounting brackets, potting and terminal arrangements.
Applications
High-frequency transformers in switch-mode power supplies and inverter welding machines.
Filter inductors and power-factor-correction chokes in solar inverters, UPS and EV chargers.
Output filtering of motor drives.
Magnetic sensors and saturable components.
Comparison with Other Core Types
| Parameter | Amorphous C-core | Mn-Zn ferrite | Powder core (sendust) |
|---|---|---|---|
| Saturation flux density | About 1.5-1.6 T | 0.3-0.5 T | About 1.0-1.6 T |
| Effective permeability | Set by gap, typically 50-2000 | 2,000-15,000 | 14-550 |
| Core loss at 10-50 kHz | Low | Very low at high frequency | Moderate |
| DC bias tolerance | Good with gap | Poor | Excellent |
| Typical use | Transformers, filter chokes | High-frequency SMPS | DC-biased inductors |
Values are typical ranges from published material data; confirm the required figures with the manufacturer data sheet for the specific grade.
Frequently Asked Questions
What is the difference between a C-core and a toroidal core?
A toroid is a continuous ring with no air gap, giving the highest effective permeability but requiring threading of the winding; a C-core is cut into two halves, allowing easy bobbin winding and a controlled air gap for DC bias and energy storage.
What does high flux mean here?
It refers to the saturation flux density of about 1.5-1.6 T, several times higher than ferrite, so the core can operate at high flux levels and stay compact.
How is the air gap controlled?
The cut faces are ground flat and the gap length is set by the grinding tolerance and, where needed, a non-magnetic spacer between the halves; the two halves are then clamped or banded together.
What frequency range suits Fe-based amorphous C-cores?
Typically from a few kilohertz up to about 50 kHz for power conversion; above this, thinner nanocrystalline ribbon or ferrite may be preferable. Confirm with the loss curves in the data sheet.
Can C-cores be used in transformers?
Yes, cut cores are used in flyback and push-pull transformers where the controlled gap stabilizes the inductance and stores energy, and where easy winding of the primary and secondary is important.
How do I order a customized C-core?
Specify the required dimensions, gap length or effective permeability, operating frequency, flux density, inductance, winding space and coating; the manufacturer then confirms the design and test values before production.

