Precisely Slitted Silicon Steel Coils: Tolerances, Burr Control and Applications
Sep 30, 2025
Leave a message
Why Slitting Accuracy Matters
The magnetic performance of silicon steel is sensitive to dimensional accuracy. A transformer core is assembled from thousands of individual laminations, and if the strip width varies, the core stack becomes irregular, the stacking factor drops and the magnetic circuit is disturbed. Even more important, a poor slitting cut leaves burrs on the strip edge; when laminations are stacked, burrs can penetrate the interlaminar insulation and create short circuits between sheets, which raises eddy current losses and can cause local overheating. Precise slitting is therefore the first quality gate in transformer core manufacturing.
Key Quality Parameters
Three parameters define the quality of a slitted coil. Width tolerance is the deviation of the strip width from the ordered value; a typical production tolerance is plus or minus 0.1 mm, and tighter values can be held on dedicated lines for the most demanding grades. Burr height is the raised edge left by the shear, and a typical acceptance limit is 0.03 mm maximum, with lower values for 0.20 mm material. Camber describes the lateral curvature of the strip along its length; low camber is essential because a curved strip causes misalignment in automatic stacking and winding equipment. In addition, the recoiling tension must be uniform so that the narrow coils wind tightly without telescoping or edge damage.
Slitting Line Considerations
Slitting of electrical steel is performed on a line with precision rotary knives, a strip tension system and a recoiler. The knife clearance and overlap must be matched to the strip thickness, because the magnetic material is brittle and cracks easily at the cut edge if the tooling is wrong. Pneumatic tension units control each strand independently, which keeps the recoiled narrow coils uniform. After slitting, the edges are inspected for burr and the width is measured with a micrometer; high-volume lines use in-line optical gauging that records the width profile of every coil. It is good practice to request an edge inspection certificate with each slit coil delivery.
Typical Grades and Strip Widths
Slit coils are supplied in both grain-oriented and non-oriented electrical steel. Grain-oriented grades such as B20R065, B23R085, B27RK085, 23Q110 and 27Q120 are used for transformer cores, while non-oriented grades such as 50W470 and 50W600 are used for motor and generator laminations. The table below summarises the typical supply range.
| Parameter | Typical Range |
|---|---|
| Strip width | 35 mm to 1200 mm |
| Thickness | 0.20 mm to 0.50 mm |
| Width tolerance | Plus or minus 0.1 mm, tighter on request |
| Max burr height | 0.03 mm typical |
| Coil inner diameter | Commonly 508 mm or 610 mm, customisable |
| Standards | GB/T 2521.1, GB/T 2521.2, IEC 60404-8-1, IEC 60404-8-7 |
Applications
Slit strip is the direct input for transformer core production, where it is punched into E and I laminations, cut into C-core strip, or wound into toroidal and rectangular cores. It is also used for the cores of current transformers, reactors, ballasts and small motors. Because the strip is delivered at final width, the core manufacturer avoids internal slitting and can concentrate on punching, stacking and annealing, which shortens the production cycle and reduces scrap.
Common Misconceptions
First, a clean edge is not the only criterion: the magnetic properties of the strip must also be verified, because slitting itself does not improve or restore the steel. Second, narrower strips are not automatically more accurate; the same width tolerance applies across the range, and very narrow strands are actually harder to keep straight because camber effects are more visible. Third, edge burr cannot be eliminated by higher slitting speed or blunt knives; only correct tooling and regular inspection keep burr within the limit. Finally, a coil certificate should always state the heat number and measured magnetic values, because traceability of the material is part of the quality system required by ISO 9001 based production.
FAQ
What is the standard width tolerance for slit silicon steel strip?
A typical production tolerance is plus or minus 0.1 mm, with tighter tolerances available for special applications. The agreed tolerance should be stated in the purchase order and verified on the coil certificate.
Why is burr control important for transformer cores?
Burrs on the strip edge can penetrate the interlaminar insulation during stacking, creating short circuits between laminations that increase eddy current losses and cause local overheating.
What does camber mean and why does it matter?
Camber is the lateral bow of the strip along its length. High camber causes misalignment in punching and stacking equipment and produces poor core geometry, so low camber is a key acceptance criterion for slit coils.
Can slit coils be supplied for both grain-oriented and non-oriented steel?
Yes. Grain-oriented grades are supplied mainly for transformer cores, and non-oriented grades for motor and generator laminations, in thicknesses from 0.20 mm to 0.50 mm and widths from 35 mm to 1200 mm.
What documentation should accompany a slit coil delivery?
A mill test certificate with heat number, grade, thickness, width, measured core loss and induction values, together with an edge inspection report for burr and width, is standard practice for certified production.

