Low Loss High Permeability Core for Oil-Filled Distribution Transformers

Oct 09, 2025

Leave a message

Core Construction of an Oil-Filled Distribution Transformer

The magnetic core of an oil-filled distribution transformer is built from stacked laminations of grain-oriented silicon steel. The sheet is cut to shape, stacked to the required window and limb dimensions, and clamped so that the finished core forms a closed magnetic circuit around the windings. Each lamination is coated with a thin insulating layer that interrupts eddy currents circulating between sheets, so the core converts the largest possible share of input power into output power and generates the least possible heat. The whole assembly is immersed in insulating oil inside a sealed tank, which carries heat away from the core and windings to the radiator surfaces and protects the internal insulation system from moisture and contamination.

Why Low Loss, High Permeability Silicon Steel Is Used

Silicon steel is chosen because its low hysteresis loss minimises the energy dissipated every time the alternating current reverses and the flux in the core changes direction. Raising the silicon content increases electrical resistivity, which suppresses eddy current loss as well; aligning the grain structure with the rolling direction adds high permeability, so a smaller core can carry the required flux with a smaller magnetising current. Together these properties deliver the two figures that matter most in distribution transformer design: low no-load loss and low exciting current. Loss reduction also lowers the temperature rise of the core, which reduces thermal stress on the oil and on the paper insulation and supports the long service life expected from oil-immersed distribution units. Oil-immersed designs are also valued for their high dielectric strength, higher overload capability than dry-type units, and effective heat dissipation under sustained load.

Grade Data: Core Loss, Induction and Lamination Factor

Oriented grades for distribution transformer cores are commonly specified by thickness, specific core loss at 1.7 T and 50 Hz or 60 Hz, minimum induction and lamination factor. The table below lists representative grades, including conventional, high-induction and domain-refined types. Customised sizes are available within the width range.

Grade family Grade Thickness (mm) Density (kg/dm3) P17/50 (W/kg) P17/60 (W/kg) Min induction (T) Lamination factor
Conventional C23Q110 0.23 7.65 1.10 1.45 1.82 0.945
Conventional C23Q120 0.23 7.65 1.20 1.57 1.82 0.945
Conventional C27Q120 0.27 7.65 1.20 1.58 1.82 0.950
Conventional C27Q130 0.27 7.65 1.30 1.68 1.82 0.950
Conventional C30Q120 0.30 7.65 1.20 1.58 1.82 0.955
High induction C23QG085 0.23 7.65 0.85 1.12 1.88 0.945
High induction C23QG100 0.23 7.65 1.00 1.32 1.88 0.945
High induction C27QG090 0.27 7.65 0.90 1.19 1.88 0.950
High induction C27QG110 0.27 7.65 1.10 1.45 1.88 0.950
High induction C30QG105 0.30 7.65 1.05 1.38 1.88 0.955
Domain refined C23QH080 0.23 7.65 0.80 1.06 1.88 0.945
Domain refined C23QH100 0.23 7.65 1.00 1.32 1.88 0.945
Domain refined C27QH085 0.27 7.65 0.85 1.12 1.88 0.950
Domain refined C30QH095 0.30 7.65 0.95 1.25 1.88 0.955
Domain refined C30QH110 0.30 7.65 1.10 1.46 1.88 0.955

Reading the table: a lower number in the core loss columns means less heat generated in the core, higher induction means a smaller core for the same rating, and a higher lamination factor means more active steel packed into the same window volume. Domain-refined grades offer the lowest loss and highest induction in the range at a higher material price.

Insulation Coating, Cutting and Core Building

Coating selection: an inorganic coating for cores that will be stress-relief annealed after cutting, a semi-organic coating where punchability and insulation must be balanced, and a self-bonding coating for stacked cores that must hold together without extra clamping.

Cutting quality: low burr height and clean shearing edges, since burrs create local short circuits between laminations and raise eddy current loss.

Stacking: step-lap or mitred joints to keep joint reluctance low, uniform clamping pressure to protect the lamination factor, and careful handling to avoid bending the sheet out of flat.

Verification: core loss and exciting current measured on the finished core, together with dimensional checks on window height, window width and stack build.

Documentation: mill test reports for each heat, covering grade, thickness, specific core loss, induction and lamination factor, so incoming inspection can confirm the delivered material.

Applications and Material Selection Guidance

Oil-immersed distribution transformers are used in utility distribution networks, where they step voltage down from transmission or sub-transmission levels; in industrial facilities that need a stable supply with good overload capability; and in commercial and residential developments that depend on consistent power delivery. Selection starts with the required no-load and load loss limits, which follow from the efficiency class the transformer must meet. From there the designer chooses thickness, grade family and core geometry together: thinner sheet lowers eddy current loss but increases the number of laminations to stack, while high-induction grades allow a more compact core. Where noise limits are tight, magnetostriction and joint design become as important as the loss figure. Matching the grade to the working flux density, frequency and efficiency target is the fastest way to reach the required loss level without overspecifying material.

Frequently Asked Questions

Q: What are the main advantages of an oil-filled distribution transformer core?
The insulating oil dissipates core and winding heat efficiently, provides high dielectric strength, protects internal parts from moisture and contamination, and allows a higher overload capacity than dry-type designs.

Q: Why is grain-oriented steel used instead of non-oriented steel in these cores?
The flux path in a transformer is fixed by the winding geometry, so the high permeability and low loss available along the rolling direction of oriented steel are fully exploited. Non-oriented steel suits rotating machines where the flux direction changes.

Q: What does the P17/50 value represent?
It is the maximum specific core loss in watts per kilogram measured at a peak flux density of 1.7 T and 50 Hz. P17/60 is the same measurement at 60 Hz, and both are quoted for a defined sheet thickness.

Q: Which thickness should be selected for a distribution transformer core?
0.23 mm and 0.27 mm oriented grades are the usual choice for distribution cores, with 0.30 mm used where a slightly thicker, more economical sheet still meets the loss requirement.

Q: How does lamination factor influence the design?
A higher lamination factor means more magnetic steel occupies the same core volume, so a smaller and lighter core can produce the same flux, reducing both material consumption and overall transformer mass.

Q: Is stress-relief annealing always required after cutting?
Not always. It depends on the coating type and on how much strain the punching or shearing process introduced. Where it is used, an inorganic coating is required because it survives the annealing temperature without losing its insulating function.

Send Inquiry