Cold Rolled Stainless Steel: Tempers, Standards and How to Specify a Coil
Jan 31, 2024
Leave a message
What Cold Rolling Does to Stainless Steel
Cold rolled stainless steel is produced by reducing the thickness of annealed and pickled hot-rolled coil between rolls at ambient temperature. No heat is used to soften the metal, so the deformation is absorbed by the crystal lattice: dislocations multiply, they obstruct each other's movement, and the material work hardens. The visible result is a stronger, harder and more dimensionally accurate strip with a much better surface finish than the hot-rolled starting stock, at the cost of ductility.
The process also sets the final mechanical condition. By stopping the mill at a defined reduction, the producer delivers a specific temper rather than a specific strength, and the temper decides both the minimum tensile strength and the minimum bend radius the customer can form. Cold rolling is therefore not a single product but a family of conditions, and the ordering specification must state the temper as well as the grade, thickness, width and surface finish.
Tempers and Mechanical Property Data
For austenitic sheet and strip, the cold-worked tempers are defined in ASTM A666, which assigns a minimum tensile strength and a minimum elongation to each temper. The table below gives representative minimum tensile strengths for Type 304 austenitic stainless steel; exact values depend on grade, product thickness and product form, and the specification always governs.
| Temper condition | Typical minimum tensile strength | Forming expectation |
|---|---|---|
| Annealed | about 515 MPa | Severe forming, deep drawing |
| Quarter hard | about 860 MPa | Simple bending, light forming |
| Half hard | about 1035 MPa | Bending to approximately 90 degrees |
| Full hard | about 1275 MPa | Limited bending, high springback |
Two consequences follow for the buyer. First, strength and formability move in opposite directions: the temper that gives the highest yield strength gives the smallest permissible bend radius and the largest springback. Second, hardness is a convenient shop-floor proxy but not a specification; a hardness reading does not define tensile strength, and disputes are settled by tensile testing to the applicable standard.
The Standards Framework
Cold rolled stainless steel is bought against a chain of specifications rather than a single document. The material specification defines the grades and their chemical and mechanical requirements; the general requirements specification defines tolerances, surface condition and inspection rules; and where structural application or a specific temper is involved, a further specification defines the cold-worked condition.
ASTM A240/A240M: chromium and chromium-nickel stainless steel plate, sheet and strip for pressure vessels and general applications. This is the usual grade reference for Types 304, 316L, 430 and similar.
ASTM A480/A480M: general requirements for flat-rolled stainless and heat-resisting steel plate, sheet and strip, covering thickness and width tolerances, flatness, edge condition, finish designations such as 2B and No. 4, and permissible variations.
ASTM A666: austenitic stainless steel sheet, strip and plate for structural applications, which is the reference for the annealed to full-hard temper sequence.
EN 10088-2: the European specification for stainless steel sheet and strip for general purposes, with its own designation system and tolerance tables.
GB/T 3280: the Chinese standard for cold rolled stainless steel plate, sheet and strip.
JIS G 4305: the Japanese cold-rolled stainless steel sheet and strip specification.
Differences between these documents are real. Tolerances, mechanical property tables and surface finish designations do not map one to one, so a drawing that cites one standard and a purchase order that cites another will always produce disputes at goods-in inspection.
Surface Finish and Tolerances
Finish designations describe both the rolling route and the final treatment. A 2B finish is cold rolled, heat treated, pickled and then lightly rolled on polished rolls, giving a smooth, grey, moderately reflective surface that is the standard engineering finish. A BA finish omits the pickle and bright anneals instead, producing a highly reflective surface used where appearance matters. A No. 4 finish is a polished finish produced with abrasive belts and gives a directional, satin appearance that is common on visible architectural components. Each finish has its own roughness expectation and its own tolerance for surface defects, and roughness should be specified numerically if appearance is critical.
Thickness tolerance is usually the most commercially important variable, because it is bought and paid for by weight whereas it is used by area and by strength. Thin strip is specified to tighter tolerance on average thickness and to a defined variation within a coil. Width tolerance, camber, edge condition and flatness follow the same logic: each is defined in the general requirements specification, and each affects material yield in the customer's press or folder.
Forming, Springback and Corrosion Effects
Work hardening changes the forming behaviour of the sheet in ways that matter on the shop floor. Yield strength rises faster than tensile strength, so the springback after bending increases, and a die set up for annealed material will not produce the same angle in a half-hard coil. Bend radii must be increased as the temper hardens, and the bend line should be kept away from sheared edges where a burr can initiate a crack.
There is a corrosion consequence as well. Cold work in austenitic grades such as 304 and 316 can induce partial transformation of austenite to martensite, particularly at heavily deformed sheared edges, and that transformed phase is less corrosion resistant than the parent austenite. In chloride-bearing service this is why a heavily cold-worked or badly sheared component can show preferential attack along a cut edge even though the sheet itself is fully compliant. Stress corrosion cracking risk also rises with the residual stress left in the material, which is one reason stress relief or a more formable temper is specified for aggressive environments.
Specifying a Coil Correctly
State the grade and its standard designation, plus any restriction such as a maximum carbon or a minimum molybdenum content.
State the temper by its standard name, not by a hardness target and not by a strength number pulled from a general table.
State thickness, width, edge condition and coil dimensions, each with a tolerance referenced to a named standard.
State the surface finish by its standard designation and add a roughness limit if appearance is functional rather than decorative.
State the inspection documents required and the tests to be witnessed, including any tensile test location and direction relative to the rolling direction.
State the intended forming operation, because that is the fact that lets the producer reject an impossible combination of temper and bend radius before the coil is rolled.
Frequently Asked Questions
Q: What is the difference between cold rolled and hot rolled stainless steel?
A: Cold rolled strip is reduced in thickness at ambient temperature, which work hardens it and gives tight tolerances and a smooth finish, while hot rolled material is processed above the recrystallisation temperature and is softer and less accurate dimensionally
Q: Does cold work make stainless steel less corrosion resistant?
A: It can. Cold work in austenitic grades can transform part of the austenite to martensite, especially at heavily sheared edges, and that phase is less corrosion resistant than the parent structure
Q: What does the 2B finish mean?
A: It is a cold rolled, heat treated, pickled and lightly rolled finish that produces a smooth grey surface; it is the standard engineering finish and its tolerances are defined in ASTM A480/A480M
Q: Why can the same grade have very different strengths?
A: Because temper, not grade, sets the strength: the same grade in the annealed condition and in the full-hard condition differs by hundreds of megapascals of tensile strength
Q: What should a purchase order state for a cold rolled coil?
A: Grade, temper, thickness, width, edge condition, surface finish, tolerances with the referenced standard, coil dimensions and the required inspection documents, plus the intended forming operation
Q: What is springback and why does it matter?
A: It is the elastic recovery of the sheet after the bending force is removed; higher yield strength from cold work increases springback, so dies set for annealed material do not produce the intended angle in a harder temper

