Transformer Voltage Regulation: Off-Circuit Taps and On-Load Tap Changers

Jan 24, 2024

Leave a message

What Voltage Regulation Means in a Transformer

A transformer delivers a voltage ratio fixed by the turns of its windings (N1/N2). In real service the secondary voltage drifts with load current, power factor and the level of the incoming supply. Voltage regulation is the deliberate change of that ratio so the outgoing voltage stays inside the limits required by the connected equipment.

Two quantities are often confused. Regulation percentage describes how much the secondary voltage falls between no-load and full load at a defined power factor, calculated as (U0 - U)/U x 100%. Tap changing is the mechanism used to compensate for that fall. A distribution transformer with 6.5% short-circuit impedance and a 0.8 lagging power factor commonly shows regulation in the region of 4% to 5%, which is exactly why a tapping range is provided at all.

Off-Circuit (No-Load) Tap Changing

Off-circuit tap changers, also called de-energized tap changers, move the tap only while the transformer is isolated. A five-position link or handwheel selects +5% or +2 x 2.5% around rated voltage in 2.5% steps. Because the ratio is changed with no current flowing, the contacts are simple, inexpensive and almost maintenance free.

Typical tapping range: +5% in 2.5% steps, or +2 x 2.5% where wider compensation is needed.

Operation: transformer de-energized, tap position locked and recorded in the commissioning log.

Design basis: IEC 60076-1 and GB/T 1094.1 for power transformers, with tap changer requirements per IEC 60214-1.

Almost all cast-resin dry-type distribution transformers use off-circuit tapping. It suits steady loads where the supply level is stable and a seasonal adjustment once or twice a year is sufficient.

On-Load Tap Changing

An on-load tap changer moves the tap while the transformer carries current. The diverter switch transfers current through transition resistors or vacuum interrupters so that no winding section is short-circuited during the transition. The result is continuous voltage correction without an outage.

Typical tapping range: +-8 x 1.25% or similar multi-step designs, normally applied to the high-voltage winding.

Switching principle: resistive or reactive transition, with vacuum interrupter diverter switches on modern units.

Typical duty: transmission and sub-transmission transformers in networks with wide daily load swings and large renewable infeed.

Cost and maintenance burden are substantially higher than for an off-circuit tap. The diverter switch needs periodic inspection, the motor drive and automatic voltage relay add control complexity, and a failure of the changer is a failure of the transformer.

Turn Ratio Control and the Tap Position Table

Every tap corresponds to a number of active turns in the tapped winding. With the tap placed on the high-voltage winding, adding turns lowers the secondary voltage and removing turns raises it. The nameplate therefore carries a tap table that links each tap number to the high-voltage value, the low-voltage value and the resulting ratio.

Method Tapping range Operates under load Typical application Relative cost
Off-circuit tap changer +5% or +2 x 2.5% No Distribution and dry-type transformers Low
On-load tap changer Multi-step, about 1.25% per step Yes Power transformers, fluctuating networks High
Series and coarse-fine winding Application specific No Rectifier and special transformers Medium

Dry-Type and Oil-Immersed Transformers Compared

Cast-resin dry-type transformers and the equivalent GB/T 10228 designs are covered by IEC 60076-11, with insulation classes F or H and cooling options AN or AF. Their tapping is nearly always off-circuit, at +5% or +2 x 2.5%, because the load they serve, such as building services, data centres or industrial drives, is seldom re-dispatched. Oil-immersed distribution transformers follow the same off-circuit practice, while large oil-immersed power transformers are the main users of on-load tap changing equipment.

When a project mixes both types, protection and control settings must account for the different regulation behaviour. A dry-type unit without an on-load changer cannot correct a sustained voltage rise caused by distributed generation connected on its secondary side.

Commissioning and Maintenance Checks

Confirm that the tap position shown on the nameplate matches the actual link or handwheel position before energizing.

Measure the turns ratio at every tap with a turns ratio tester and compare the results with the tap table.

Record winding resistance per phase to detect loose tap links or poor contact resistance.

On dry-type units, check tap link torque and clean contact surfaces; on changer-equipped units, review diverter switch operation counts.

Log regulation performance after load pickup to decide whether the tap position should be reset.

Frequently Asked Questions

Q: Can a dry-type transformer be supplied with an on-load tap changer?
It is technically possible but uncommon. Vacuum on-load changers are available for cast-resin designs, yet the extra cost and maintenance are difficult to justify for building or industrial loads. Most dry-type projects are better served by an off-circuit tap at +5%.

Q: Which tap position should be used at commissioning?
Start at the position that corresponds to the measured supply voltage. If the incoming voltage is above nominal, move the tap to reduce the turns ratio difference and re-measure the secondary voltage under load.

Q: How often should an off-circuit tap be adjusted?
Only when the supply level changes seasonally or after a network reconfiguration. The transformer must be de-energized and the position recorded each time.

Q: Does a wider tapping range improve performance?
Not by itself. A wider range adds winding cost and slightly increases losses. Specify the range that covers the real supply variation, typically +-5%, and keep the number of steps practical.

Q: What causes the secondary voltage to drift under load?
Winding impedance, load power factor and load current. The larger the short-circuit impedance and the lower the power factor, the greater the drop that tap changing has to compensate.

Q: Are tap changers covered by routine factory tests?
Yes. Ratio measurement at every tap, winding resistance and operational checks of the changer mechanism are standard routine tests before dispatch.

Send Inquiry