Corrosion Resistant Nanocrystalline C-Type Core: Properties and Applications

Oct 22, 2025

Leave a message

What a Corrosion-Resistant Nanocrystalline C-Type Core Is

A corrosion-resistant nanocrystalline C-type core is an iron-based soft magnetic core wound from nanocrystalline alloy strip. The alloy has an ultrafine grain structure, typically in the range of 10 to 20 nanometres, which gives it a rare combination of high permeability and low loss. The finished core is sealed with an epoxy or equivalent protective coating so that moisture, abrasion and aggressive atmospheres cannot attack the magnetic strip. The C-shape, also called a C-core, provides a defined and controllable air gap, which makes the part suitable for inductors, chokes and transformers that need precise magnetic design.

Magnetic and Mechanical Advantages

High saturation flux density: around 1.2 to 1.25 T, so the core stays linear at useful excitation levels.

Ultra-high initial permeability: up to about 80,000 or more after annealing, which allows a high inductance with few turns.

Low core loss: typically 15 to 30 W/kg at 100 kHz, depending on flux density and frequency.

Wide frequency range: usable from 50 Hz to beyond 100 kHz, covering power-frequency and switched-mode duties.

Compact size: the strong magnetic properties allow smaller, lighter transformers and chokes, which matters in space-constrained designs.

Corrosion resistance: the epoxy coating resists moisture and abrasion, giving reliable long-term operation in humid or mildly corrosive environments.

Typical Parameters

Parameter Typical value
Saturation induction Bs 1.2 - 1.25 T
Initial permeability 80,000 or higher after annealing
Core loss at 100 kHz 15 - 30 W/kg, frequency dependent
Curie temperature 560 degrees C or higher
Operating frequency 50 Hz to 100 kHz and above
Protective coating Epoxy, moisture and abrasion resistant

Geometry and Customisation

C-type cores are described by a family of dimensional parameters that define the window opening and the overall core envelope. Datasheets list these parameters with tolerances, commonly from plus or minus 0.5 mm on small builds to plus or minus 1.5 mm on the largest ones. Because the air gap is set by the C-shape and by the mating of the two halves, the inductance and the saturation behaviour of the finished component can be tuned by selecting a suitable window size and build width instead of changing the winding. Outside dimensions are not restricted to a catalogue: any build can be produced to a customer drawing, and non-standard window widths, stack heights and core lengths are developed on request, including sample batches for magnetic performance verification.

Applications and Working Environment

The combination of high permeability and low loss makes these cores first choice for high-frequency transformers, switch-mode power supplies, inverters, EMI common-mode chokes, current sensors and inductors in renewable-energy converters. In each case the design team should state the required saturation flux density, the target permeability, the working frequency and, for humidity or offshore duties, the exact environmental conditions so that the correct coating system and gap tolerance can be selected. Cores intended for equipment with long service intervals should also be assessed for the maximum operating temperature that the winding insulation allows, keeping a margin below the Curie temperature of the alloy.

Frequently Asked Questions

Q: What makes a nanocrystalline core corrosion resistant?
The alloy strip is protected by an epoxy or equivalent coating that resists moisture, abrasion and environmental stress, so the core can serve in humid or mildly corrosive atmospheres.

Q: Why is a C-type core used instead of a toroid?
The C-shape provides a defined air gap and lets the winding be assembled around the core, which is convenient for high-power chokes and transformers that need precise inductance control.

Q: What is the saturation flux density of nanocrystalline alloy?
Typically about 1.2 to 1.25 T, which is higher than ferrite and supports compact designs with good overload margin.

Q: What frequency range can these cores cover?
From 50 Hz up to 100 kHz and beyond, so the same alloy family suits power-frequency chokes and high-frequency switched-mode transformers.

Q: Can non-standard core dimensions be produced?
Yes. Window width, stack height and core length can be built to a project drawing, and sample batches are available for performance verification before series production.

Q: How is core loss quoted?
As a specific loss in watts per kilogram at a stated flux density and frequency, such as the 15 to 30 W/kg band measured at 100 kHz for this alloy.

Send Inquiry