Can Galvanized Steel Be Welded?
Feb 28, 2024
Leave a message
Galvanized steel can be welded, and with the correct welding consumables, surface preparation and ventilation it can be joined without weakening the base metal. The practical difficulties come from the zinc coating itself: zinc melts at about 420 °C and boils at about 907 °C, well below the melting point of steel (about 1500 °C). During welding the zinc in the joint zone vaporizes, which affects the weld pool, produces fumes that must be controlled, and removes the corrosion protection locally. This article explains how to weld galvanized steel correctly and how to restore the coating afterwards.
Why the Zinc Coating Complicates Welding
When the arc or flame heats the joint, the zinc coating burns off and vaporizes, causing four well-known effects:
Zinc fume generation: zinc oxide fumes are released and, if inhaled in quantity, can cause metal fume fever (flu-like symptoms). Ventilation and respiratory protection are mandatory.
Porosity: zinc vapor may be trapped in the solidifying weld pool, creating gas pores that weaken the weld.
Spatter and arc instability: zinc vapor disturbs the arc and increases spatter, so welding parameters must be adjusted.
Loss of corrosion protection: the coating is destroyed in and around the weld, and must be repaired to prevent rust at the joint.
Recommended Welding Processes
Most common arc welding processes can join galvanized steel if the parameters are adapted:
GMAW (MIG): preferred for sheet and light sections; use a slightly higher travel speed and a slightly lower voltage than for bare steel to limit zinc burn-off, and position the gun angle to push the zinc vapor away from the pool.
GTAW (TIG): gives good control and low spatter for thin material; clean the zinc from the joint area first to avoid porosity.
SMAW (stick): workable with rutile or basic electrodes; keep the arc short and remove spatter between passes.
Resistance spot welding: widely used for galvanized sheet in automotive work; the coating improves electrode life compared with bare steel in some conditions, but welding current must be increased slightly.
Filler metals are selected per AWS A5 classifications for the base metal strength; for carbon steel galvanized sheet, standard carbon-steel fillers are normally used once the zinc is removed from the joint faces.
Joint Preparation and Welding Technique
The most reliable method is to remove the zinc coating from the joint area before welding:
Grind or wire-brush the zinc away from the weld zone, typically 25–50 mm on each side of the joint, and clean off the dust.
For thin sheet, minimize burn-through by using smaller diameter electrodes and lower heat input.
Keep the arc on the prepared steel rather than dwelling on the coated edges.
After welding, remove slag and spatter completely, because spatter that contains zinc can be a corrosion initiator.
Where the coating cannot be removed (for example, on galvanized tubing or in field repair), accept higher spatter and porosity risk and compensate with careful parameter selection and post-weld inspection.
Fume Safety and Exposure Limits
Zinc oxide fume is the main hazard when welding galvanized steel. Occupational exposure limits for zinc oxide fume are set at 5 mg/m³ (time-weighted average) under OSHA and at 2 mg/m³ under ACGIH guidance. Practical controls include:
Local exhaust ventilation positioned close to the arc, or fume extraction guns.
Respiratory protection for confined spaces and poorly ventilated work.
Good general workshop ventilation; do not weld galvanized steel in enclosed spaces without extraction.
Washing hands before eating or smoking, since zinc dust on the skin can be ingested.
Metal fume fever is temporary, but repeated high exposure should be avoided; the controls above keep exposure below the limits.
Post-Weld Coating Repair
The weld zone loses its galvanized protection, so the coating must be restored. ASTM A780, Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings, describes three accepted repair methods:
Zinc-rich paint: applied to cleaned steel in the damaged area; the zinc loading must meet the standard's requirements.
Zinc thermal spray (metallizing): molten zinc is sprayed onto the prepared surface, giving a coating close in behavior to hot-dip zinc.
Zinc-based solder: applied with a soldering iron or torch where paint or spray is impractical.
Before repair, the weld area must be cleaned of slag, spatter and rust. The repaired coating thickness should match the original coating class as closely as practical, and for structural work the repair method should be specified in the project documents.
Frequently Asked Questions
Q: Is it safe to weld galvanized steel indoors?
Only with effective local exhaust ventilation or respiratory protection, because welding generates zinc oxide fume. In confined spaces, forced ventilation and supplied-air or high-efficiency respirators are required to stay below the exposure limits.
Q: Does welding weaken galvanized steel?
If the joint is prepared correctly and the welding parameters suit the section thickness, the weld strength is essentially the same as for uncoated steel of the same grade. The main risks are porosity and incomplete fusion if the zinc is not managed.
Q: Should the zinc be removed before welding?
It is recommended and often required for critical welds. Removing the zinc from the joint faces (25–50 mm each side) eliminates most porosity and spatter problems and makes the weld easier to inspect.
Q: Why does the weld zone rust faster after welding?
The heat destroys the zinc coating in and around the weld, leaving bare steel that corrodes quickly unless the coating is repaired. Always repair the damaged coating with a method accepted by ASTM A780.
Q: Can galvanized pipe be welded to fittings?
Yes, but the zinc must be removed from the joint area before welding and the joint should be protected afterwards. Threaded or mechanical joints are sometimes preferred for galvanized pipe to avoid welding altogether.
Q: What is metal fume fever?
Metal fume fever is a temporary flu-like illness caused by inhaling zinc oxide fume, with symptoms starting a few hours after exposure and resolving within 24–48 hours. It is preventable with ventilation and respiratory protection.

