B23P090 Premium CRGO Transformer Iron Core for High-Efficiency Energy

Oct 21, 2025

Leave a message

Product Overview

The B23P090 CRGO transformer iron core is a high-grade magnetic core built from cold-rolled grain-oriented silicon steel of the B23P090 class. The designation means a nominal thickness of 0.23 mm and a guaranteed maximum core loss of 0.90 W/kg measured at 1.7 T and 50 Hz. Cores of this class combine extremely low iron loss with high permeability, which makes them the preferred choice for distribution transformers, small power transformers and instrument transformers where energy efficiency and stable voltage are required.

Why Silicon Steel Is Used for Transformer Cores

Low Core Losses

Silicon steel has low hysteresis loss and, when laminated, low eddy-current loss under alternating flux. The energy that would otherwise be wasted as heat is minimised, so the transformer runs cooler and more efficiently.

High Magnetic Permeability

The material magnetises and demagnetises easily in response to alternating current, which lets the core transfer flux between the primary and secondary windings with a small magnetising current.

High Saturation Flux Density

Grain-oriented electrical steel saturates at about 2.03 T at room temperature, so the core can carry high flux levels without losing its magnetic properties, keeping the transformer stable under voltage excursions.

Laminated Construction

Thin laminations insulated from each other break up the eddy-current paths in the core. The same physics applies to the thin strip of wound cores: the thinner the strip, the lower the eddy-current component of the loss.

B23P090 Grade Data

Property Value
Nominal thickness 0.23 mm
Max core loss at 1.7 T / 50 Hz 0.90 W/kg
Min induction at 800 A/m (B800) 1.88 T
Lamination factor 97.2 %
Typical width 35-1200 mm (slit widths available)

For comparison, a conventional 23Q110 grade guarantees 1.10 W/kg at the same induction, so the high-induction B23P090 saves roughly 18 % of the core loss while providing a higher working flux density.

Core Manufacturing and Assembly

Transformer cores are produced by cutting the CRGO strip to precise dimensions, stacking the laminations with mitered corner joints, and clamping the stack to a controlled pressure. Core workshops handle automatically stacked cores up to 60 t and manually stacked cores up to 120 t. Joint gaps are held below 1.0 mm, and window height and width are machined to ±1 mm accuracy, which directly controls the magnetising current and noise of the finished transformer. Wound cores are built by slitting the strip to width, winding it on a mandrel and annealing, and are used where a fully closed magnetic circuit is required.

Material and Quality Control

The raw material is premium CRGO silicon steel with a silicon content of roughly 0.5-4.5 %, supplied from qualified mills with full mill test certificates. Incoming coils are checked for thickness, core loss and coating condition; lamination factor is verified during stacking; and the finished core is tested for dimensions, joint gap and surface insulation before packing. Magnetic verification follows IEC 60404-2 for Epstein measurement and GB/T 2521.2 for grade compliance, with ASTM A876 recognised for markets applying US practice.

Applications

Distribution transformers and pad-mounted transformers

Small and medium power transformers

Reactors and magnetic amplifiers

Current and potential transformers

Welding transformers and magnetic switch cores

Selection Notes

Choose the core grade by balancing first cost against the capitalised value of the no-load loss. For transformers that run continuously, a premium grade such as B23P090 or a domain-refined B23R085 often pays back within a few years. Also specify the core loss tolerance and the maximum joint gap explicitly in the purchase order, because these two parameters dominate the actual performance of the finished transformer. Core dimensions should always be supplied as a drawing with window sizes, stack height and clamping details.

FAQ

What does B23P090 mean exactly?

B indicates grain-oriented silicon steel, 23 the nominal thickness in hundredths of a millimetre (0.23 mm), P the high-induction grade family, and 090 the guaranteed maximum core loss of 0.90 W/kg at 1.7 T/50 Hz.

How much energy can a premium core save?

Compared with a conventional 23Q110 core, the B23P090 grade cuts core loss by about 18 % at the same induction. Over a 20-year service life, the saving on no-load energy of a continuously energised transformer easily exceeds the price difference of the material.

What is the lamination factor and why does it matter?

The lamination factor is the ratio of solid steel to the total volume of the core including coatings. A factor of 97.2 % means less coating and air occupies the stack, so the designer achieves the target flux density with a smaller, lighter core.

Can the core be supplied in wound form?

Yes. The same grade can be slit and wound into toroidal or C-cores, which removes the joint gaps of stacked cores entirely and further reduces the excitation current.

How is the joint gap controlled in stacked cores?

The gap is controlled by the accuracy of the miter cutting, the flatness of the laminations and the stacking method. Precision tooling and strict dimensional inspection keep the gap below 1.0 mm as standard.

Send Inquiry