630 kVA 10kV Dry-Type Transformer: Impedance Voltage and Load Adaptability

Jan 30, 2026

Leave a message

What Is Impedance Voltage?

Impedance voltage, often written as Uk and expressed as a percentage, is the voltage that must be applied to one winding at rated frequency while the other winding is short-circuited, in order to circulate rated current. It is the vector sum of the resistive and reactive voltage drops of the transformer, and it is measured and defined according to IEC 60076-1. For a 630 kVA 10kV dry-type transformer, the impedance voltage is a fixed design value, usually stated on the nameplate, typically in the range of 4% to 8%.

Why Impedance Voltage Matters

Short-circuit current limitation

The symmetrical short-circuit current is approximately the rated current divided by the impedance (as a decimal). A unit with 6% impedance limits the fault current to about 16.7 times rated current, while a 4% unit would allow about 25 times. The chosen value must coordinate with the breaking capacity of the upstream breaker and the withstand rating of downstream equipment.

Voltage regulation

Under load, the internal voltage drop of the transformer is proportional to the impedance. A higher impedance means a larger voltage drop between no-load and full-load conditions, which can matter for sensitive equipment at the end of long feeders. The reactive component dominates in dry-type and oil-filled units alike.

Parallel operation

Transformers connected in parallel must have impedance voltages within close tolerance (typically within 10% of each other, per IEC 60076-1 guidance) so that the load shares proportionally to the ratings. A mismatch forces one unit to carry more than its share.

Typical Values for the 630 kVA 10kV Class

Parameter Typical Value Reference
Rated capacity 630 kVA IEC 60076-11
Voltage ratio 10kV / 0.4kV project
Vector group Dyn11 project
Impedance voltage 6% (common), 4% to 8% range IEC 60076-1
No-load loss 1.2 kW to 1.5 kW typical for this class
Load loss at 120°C 6.0 kW to 7.5 kW typical for this class
Insulation class F (temperature rise 100 K) or H (125 K) IEC 60076-11
Basic impulse level 75 kV (10kV class) IEC 60076-3
Sound level ≈ 62 dB(A) IEC 60076-10
Enclosure IP23 typical IEC 60529

Optimization Trade-offs

Lowering the impedance improves voltage regulation and reduces reactive losses, but raises the short-circuit current and therefore the mechanical stress on the windings during faults, which requires stronger bracing. Raising the impedance protects the network from excessive fault current but degrades regulation and increases load losses. The optimization therefore depends on the system fault level, the feeder length, and the sensitivity of the connected loads. For a 630 kVA unit feeding a 0.4kV bus with high motor content, a value around 6% is a balanced choice; the final value should be confirmed by a short-circuit study of the network.

Load Adaptability of the Dry-Type Design

Dry-type transformers use air or resin insulation and are common in buildings, tunnels, and indoor plants where oil is not allowed. IEC 60076-11 defines their temperature-rise limits, and the loading capability depends on the insulation class: class F allows 100 K average winding rise, class H allows 125 K. Because dry-type units tolerate short-term overloads within the thermal time constant, the loading guide approach can be applied with the appropriate dry-type thermal data. The impedance value also influences the overload behavior indirectly through the loss distribution between no-load and load losses.

How to Specify and Verify Impedance

The specification should state the impedance voltage at rated current, the tap position, and the reference temperature, and the routine test report should show the measured value within the manufacturing tolerance (typically ±7.5% for impedance per IEC 60076-1). When parallel operation is planned, the impedance of the units should be matched more tightly, and the phase-angle of the impedance should also be similar to avoid circulating currents.

FAQ

What does a 6% impedance voltage mean in practice?

It means that with the secondary short-circuited, 6% of rated primary voltage drives rated current. The prospective short-circuit current is therefore about 16.7 times rated current, before system impedance is added.

Can the impedance be changed after manufacture?

No. Impedance is fixed by the winding geometry, turns and disposition. Changing it requires a redesign, which is why the value must be agreed in the specification stage.

Why do two transformers in parallel need similar impedance?

Because load sharing is inversely proportional to impedance. If the impedances differ by more than about 10%, the lower-impedance unit carries disproportionately more load and can overheat.

Does a higher impedance increase losses?

The load loss (copper loss) is part of the impedance, so designs with higher impedance often have somewhat higher load loss, but the reactive component dominates and does not itself consume active power.

Is 630 kVA the largest dry-type rating available?

No. Dry-type transformers are available up to several MVA, but 630 kVA is a very common rating for building and industrial distribution because of its compact size and good balance of capacity and cost.

In summary, impedance voltage is one of the most consequential parameters of a 630 kVA 10kV dry-type transformer: it coordinates fault levels, voltage regulation and parallel operation. Specifying it deliberately, around 6% for typical distribution duty, and verifying the measured value in the test report, protects both the transformer and the network it feeds.

Send Inquiry