Common Faults and Troubleshooting Methods for 200 kVA Fluid-Immersed Transformers

Feb 03, 2026

Leave a message

Overview

A 200 kVA fluid-immersed transformer is a workhorse of small distribution networks, supplying factories, farms, commercial buildings and residential clusters. Like all oil-immersed units, its reliability depends on the condition of the oil, the integrity of the tank, and the quality of electrical connections. This guide describes the most common faults of 200 kVA fluid-immersed transformers, how to identify them, and the correct step-by-step troubleshooting procedure. All work must be carried out by qualified personnel after the transformer is de-energised, isolated and earthed.

Common Fault Categories

Oil leakage at joints, welds and gaskets

Overheating from overload, blocked cooling or high ambient temperature

Abnormal noise from loose core, resonance or supply harmonics

Insulation deterioration caused by moisture or oil ageing

Protection device operations such as gas relay trips

Oil Leakage

Symptoms and Causes

Oil stains on the tank, falling oil level in the conservator, and a slightly increased hum during operation point to leakage. Typical leak points are the bushing flanges, radiator and valve connections, cover gasket, and welds on the tank wall or base. Causes include loose fasteners, aged gaskets, vibration fatigue and corrosion.

Troubleshooting

De-energise and earth the unit, then clean the suspected area and inspect with a torch. Tighten loose joints to the specified torque, replace damaged gaskets with compatible oil-resistant seals, and repair corroded areas by grinding and welding before applying a new anti-corrosion coating. Top up with tested oil of the same type and class, and re-check the level after 24 hours. A persistent leak that cannot be located on the surface should be investigated with a pressure test of the tank per IEC 60076-1.

Overheating

Symptoms and Causes

The top-oil temperature climbs above the normal 65 K rise, the temperature alarm or trip operates, and the oil darkens faster than usual. Common causes are sustained overload, blocked radiator fins or fan failure, oil pump malfunction in ONAF units, high ambient temperature, and internal faults such as turn-to-turn short circuits.

Troubleshooting

Reduce or transfer the load immediately. Clean the radiators and fans with compressed air or low-pressure water, verify fan rotation and direction, and confirm the oil level is correct so that natural circulation works. Take an oil sample: if the breakdown voltage has fallen below 30 kV, or moisture exceeds the limit, the oil must be filtered or replaced with oil meeting GB 2536 or IEC 60296. If the temperature stays high with a light load, measure winding DC resistance and perform a turns-ratio test to check for winding faults, and arrange a dissolved gas analysis (DGA).

Abnormal Noise

Magnetostriction of the core produces the normal hum, but a loud or changing noise usually means loose core clamping, loose tank parts, resonance with the mounting structure, or excessive harmonics in the supply. Tighten core bolts and tank fittings to the maker's values, check the foundation bolts and anti-vibration pads, and record supply harmonics with a power quality analyser. If the noise appeared after a through-fault, inspect for mechanical displacement of the windings before re-energising.

Insulation and Oil Deterioration

Moisture is the main enemy of the oil-paper insulation system. It enters through breathers, leaking seals and poorly sealed conservators. Routine oil tests cover breakdown voltage, water content, acid value and dissolved gases; trending these values per IEC 60422 tells the maintenance planner when to filter, recondition or replace the oil. A rising trend of hydrogen and hydrocarbon gases in the DGA indicates a developing thermal or electrical fault and justifies a shutdown inspection.

Key Parameters of a 200 kVA Unit

Parameter Typical Value
Rated capacity 200 kVA
Primary voltage 10 kV / 20 kV (customisable)
Secondary voltage 0.4 kV (customisable)
Frequency 50 / 60 Hz
Cooling ONAN (ONAF optional)
Insulation class F (H optional)
Temperature rise limit 65 K oil; 100 K average winding per IEC 60076-2
Total weight including oil approximately 1200-1500 kg
Design standards IEC 60076, GB 1094

Preventive Maintenance Schedule

Monthly: visual inspection for leakage, oil level, abnormal noise, temperature readings

Quarterly: oil sampling for breakdown voltage and water content

Semi-annual: clean radiators and fans, tighten electrical connections, verify earth continuity

Annual: full oil analysis including DGA, protection relay test, and thermographic scan of connections

FAQ

How do I know if the oil must be replaced?

Replace or recondition the oil when the breakdown voltage is below 30 kV, the water content exceeds about 20 ppm, or the acid value exceeds 0.1 mg KOH/g. Trending the results is more reliable than a single reading.

Why does the gas relay trip shortly after oil top-up?

Trapped air in the tank or conservator pipe is the usual cause. De-gas the unit by opening the vent valves in sequence and let the unit settle before re-energising; repeated trips after proper de-gassing indicate a real internal fault and need DGA.

Can a 200 kVA transformer run on overload?

Brief overload is possible with continuous temperature monitoring, but sustained overload accelerates insulation ageing. For a predictable load increase, specify a larger rating or ONAF cooling.

What does a rising DGA hydrogen level mean?

Elevated hydrogen usually indicates partial discharge activity, for example from loose connections, moisture or voids in the insulation. Investigate promptly before the condition develops into a flashover.

Is it safe to clean the radiator with a pressure washer?

Low-pressure water is acceptable when the unit is de-energised and the electrical enclosures are covered. Never direct high-pressure water at the bushings, cable boxes or control wiring.

Send Inquiry