10 kV 125 kVA Three Phase Oil Immersed Distribution Transformer with Fully Sealed Corrugated Tank

Oct 30, 2025

Leave a message

Hermetically Sealed 125 kVA Distribution Transformer

A 125 kVA three-phase oil-immersed distribution transformer is used where a single 10 kV or 11 kV feeder has to supply more load than a 100 kVA unit can carry, but where a 160 kVA or 200 kVA frame would exceed the available pole or pad space. The rating sits between the two common sizes and is frequently specified for office developments, small hotels, workshops and water pumping installations served from a 0.4 kV board.

The fully sealed variant described here removes the oil conservator entirely. Thermal expansion of the oil is absorbed by the elastic deflection of a corrugated tank wall, so the oil never meets outside air and the two ageing mechanisms that dominate free-breathing units - oxidation and moisture ingress - are largely suppressed.

Why the Corrugated Tank Replaces the Conservator

In a conventionally conservator-equipped transformer the oil surface breathes through a silica gel breather, and every heat cycle exchanges a small volume of air with the atmosphere. In the hermetically sealed design the corrugated wall acts as the expansion element: the wall deflects as the oil volume changes, developing a compensating pressure change instead of pulling in outside air. The consequences are practical rather than cosmetic - no breather to re-charge, no oil-level gauge that needs seasonal adjustment, a lower overall tank height, and a smaller oil volume for the same rating.

The same corrugated wall also functions as a cooling surface. Fins increase the convective and radiative area, so the temperature rise required by IEC 60076-2 - 60 K top oil and 65 K average winding for ONAN units - can be met without forced cooling at this rating.

Winding, Core and Connection Arrangements

The core is stacked from grain-oriented silicon steel laminations, and the grades used are defined by IEC 60404-8-7, which guarantees the maximum specific total loss of the strip at 1.7 T and 50 Hz. Copper is used on both sides - heat-resistant enamelled wire is used for the HV winding on account of its conductivity and thermal class, while the LV winding uses foil or strip conductor to keep the radial build small and to improve short-circuit behaviour.

Available HV levels are 6 kV, 6.3 kV, 10 kV, 10.5 kV, 11 kV, 20 kV and 35 kV; LV options are 400 V, 415 V and 0.4 kV. Vector groups are selected to match the earthing arrangement of the network: Dyn11 for the usual solidly earthed LV distribution board, Yyn0 where the neutral has to be brought out, and Yd11 for two-winding configurations fed from a delta source.

Parameter Rating or range
Rated capacity 125 kVA
HV winding 10 kV / 11 kV, Um 12 kV
LV winding 0.4 kV, 0.415 kV
Insulation level, HV 75 kV peak LI, 28 kV rms AC (IEC 60076-3)
Tap range +/-2 x 2.5 % off-circuit
Cooling ONAN, corrugated wall
Temperature rise 60 K oil, 65 K winding (IEC 60076-2)
Short-circuit withstand 2 s, IEC 60076-5

Protective Devices and Operational Safety

Although the sealed tank removes the breathing route for moisture, internal faults still have to be detected. A pressure relief valve opens to vent an abnormal pressure surge caused by an internal arc or a severe overload and reseats automatically once the pressure returns to normal. A gas relay can be fitted where the tank geometry permits, giving an alarm on slow gas accumulation and a trip on sudden oil movement. A thermometer pocket accepts either a glass thermometer or a dial gauge with alarm contacts, and a pressure or vacuum gauge allows the tank condition to be checked at service visits.

Dielectric condition of the oil is verified before dispatch by power-frequency breakdown tests carried out to IEC 60156, or by the ASTM D1816 method, and oil is delivered to the IEC 60296 mineral-oil specification. Routine electrical tests follow IEC 60076-1.

Installation and Maintenance Reality

These units are built for outdoor ground or pole mounting, and the maintenance schedule reflects that: a visual inspection of bushings, gaskets, paint and the relief valve, cleaning of the corrugated walls to keep them free of dust and nesting material, and an oil sample for dissolved-gas analysis at multi-year intervals. There is no conservator oil level to top up and no breather desiccant to replace, which is the main operating attraction of the sealed design.

Frequently Asked Questions

Q: What current does a 125 kVA transformer deliver at 0.4 kV?
A: The LV line current is about 180 A (125000 / (1.732 x 400)), so the incoming LV device is normally rated 250 A with a breaking capacity matched to the fault level at the terminals.

Q: Is the fully sealed tank repairable on site?
A: Yes, provided the tank is opened under controlled conditions and the oil is processed before refilling. The design still allows the core and coils to be lifted out, but the unit must be re-dried and vacuum filled to restore the original dielectric margin.

Q: How can the oil level be checked if there is no conservator gauge?
A: The sealed tank normally carries a pressure or vacuum gauge instead of an oil-level sight glass. At a reference oil temperature the gauge reads near atmospheric; a persistent vacuum or over-pressure indicates an oil-volume or cooling problem.

Q: Does a corrugated wall reduce cooling performance?
A: No. The corrugations provide a larger effective dissipating area than a flat tank of the same footprint, which is why the ONAN temperature-rise limits of IEC 60076-2 are met without radiators or fans at this rating.

Q: Which vector group should be specified for an LV network with many single-phase loads?
A: Dyn11 is the standard answer. The delta HV winding circulates triplen harmonics, and the LV neutral is solidly available for unbalanced single-phase loading.

Q: What is the advantage of a tap range of +/-2 x 2.5 % over +/-5 %?
A: Both give a total range of 5 % but +/-2 x 2.5 % provides four tap positions instead of two, giving finer adjustment of the LV voltage as the HV feeder voltage drifts with load.

Send Inquiry