What Causes Oil-Immersed Transformers to Overheat? Diagnosis and Prevention
Jan 26, 2024
Leave a message
Why Temperature Control Matters in Oil-Immersed Transformers
An oil-immersed transformer relies on insulating oil for both dielectric strength and heat transfer. The winding insulation, normally cellulose paper, ages according to the hot-spot temperature: per the widely used aging rule, every 6-8 °C increase above the design hot-spot temperature roughly halves the insulation life. This means overheating is not only an efficiency problem but a direct threat to the service life of the transformer, typically designed for 20-30 years of operation. Understanding the causes of overheating allows operators to detect problems early, correct them and avoid costly failures.
Main Causes of Overheating
1. Overload operation
Operating the transformer above its rated capacity increases the winding current, which raises copper losses with the square of the current. A 20% overload increases load loss by about 44%, and the resulting hot-spot temperature rise can exceed the insulation rating. Short-term overloads are allowed by standards such as IEC 60076-7, but they require careful monitoring of oil temperature and hot-spot temperature.
2. Cooling system failure
In ONAN (oil natural, air natural) designs, cooling depends on free convection and radiation from the tank and radiator fins. Blocked radiator fins, accumulated dust, damaged cooling fans in ONAF (oil natural, air forced) designs, or a low oil level all reduce heat rejection and cause the oil temperature to climb even at normal load.
3. Oil quality degradation
Transformer oil ages: moisture, oxygen and oxidation by-products reduce both its dielectric strength and its heat-transfer capability. Sludge deposits on the windings and core act as a thermal blanket, further raising the temperature. Oil testing measures dielectric strength, moisture content, acidity and dissolved gases to reveal this condition.
4. Core insulation damage between laminations
The core is made of thin silicon steel laminations coated with an insulating layer. If this coating is damaged or the laminations are short-circuited, circulating eddy currents flow through the core, generating abnormal heat. A typical symptom is frequent operation of the gas relay and higher no-load loss, detectable by measuring the no-load current and by oil analysis.
5. Loose or corroded connections
Poor contact at the tap changer, loose terminal connections or corroded internal and external wiring increase contact resistance. Under load, these hot spots generate local heating that can discolor terminals and, in severe cases, cause arcing. DC resistance measurement of the windings and tap positions is the standard detection method.
6. High ambient temperature and poor ventilation
A transformer installed in a confined space with insufficient ventilation, or operating in a hot climate, starts from a higher ambient temperature. The temperature rise limits defined in IEC 60076-2 are referenced to a maximum ambient of 40 °C; above that, the permissible loading must be reduced.
Typical Symptoms and How to Detect Them
| Symptom | Likely Cause | Detection Method |
|---|---|---|
| Oil temperature rises above normal at rated load | Cooling blockage, low oil level, overload | Oil temperature gauge, load recording, radiator inspection |
| Gas relay operates frequently | Core insulation damage, partial discharge, internal fault | Dissolved gas analysis (DGA), no-load test |
| Three-phase winding DC resistance unbalanced | Loose connection, tap changer contact problem | DC resistance test per phase and tap position |
| Oil dielectric strength drops | Moisture ingress, oil aging | Oil sampling and laboratory testing |
| Local discoloration of terminals | Poor contact, corrosion | Visual inspection, thermography |
| Abnormal voltage or current in one phase | Inter-turn fault, winding insulation breakdown | Ratio test, insulation resistance test, DGA |
Prevention and Maintenance Measures
Keep the loading within the rated capacity or follow the overload limits and duration specified in IEC 60076-7, monitoring oil temperature continuously during overload.
Clean radiator fins and check cooling fans regularly; never restrict the airflow around the tank.
Maintain the correct oil level and replace or regenerate the oil when testing shows degraded dielectric strength or high acidity.
Perform periodic no-load and load-loss measurements to detect core insulation deterioration and winding resistance changes.
Check and re-torque all bolted connections, and verify tap changer contact condition with a DC resistance test.
Ensure adequate ventilation of the transformer room and respect the ambient temperature design limits.
What to Do When Overheating Is Detected
When overheating is observed, reduce the load if possible and check the oil temperature gauge and fan operation first. If the temperature remains high, take an oil sample for dissolved gas and dielectric testing, measure the DC resistance of the three-phase windings at each tap position, and perform an insulation resistance test. If core insulation damage is suspected, the core must be lifted and inspected; repairs such as re-insulating damaged laminations or replacing the core should only be carried out by qualified personnel with the transformer de-energized and properly earthed.
FAQ
What is the normal oil temperature for an oil-immersed transformer?
For a transformer designed to IEC 60076, the top oil temperature at rated load is typically around 85-95 °C with 40 °C ambient. As a practical rule, a top oil temperature above 95-100 °C at rated load indicates a problem that should be investigated.
Can a transformer be operated above its rated capacity?
Yes, but only within defined overload limits and with continuous temperature monitoring. IEC 60076-7 provides loading guides for different insulation systems and ambient conditions; the allowed overload time shrinks quickly as the pre-load and ambient temperature increase.
Why does the gas relay operate when the core insulation is damaged?
Core insulation damage creates circulating eddy currents that heat the core locally and decompose the surrounding oil, generating gases such as hydrogen and hydrocarbons. These gases collect in the gas relay, causing it to alarm or trip.
How often should transformer oil be tested?
For distribution transformers, an annual oil sample for dielectric strength and moisture is common; dissolved gas analysis is recommended every 1-3 years or after any suspected fault, overload or relay operation. The frequency depends on the voltage class and the criticality of the unit.
Does high ambient temperature really shorten transformer life?
Yes. Insulation aging is exponential with temperature. Operating at a hot-spot temperature 10 °C above the design value can halve the insulation life. That is why derating factors are applied for installations above 1,000 m altitude and in hot climates.
What is the most common cause of overheating in practice?
For distribution transformers, the most common causes are sustained overload, blocked cooling surfaces and oil degradation. Loose connections and core insulation damage occur less frequently but are more serious when they do happen, so they should be checked whenever overheating is accompanied by gas relay operation or unbalanced resistance readings.

