Galvanized Steel Coil: Main Advantages, Process and Applications

Dec 05, 2023

Leave a message

What Is Hot-Dip Galvanized Steel Coil?

Hot-dip galvanized steel coil (GI coil) is a cold-rolled steel strip that is continuously passed through a bath of molten zinc at about 450 °C, so that a metallurgically bonded zinc coating forms on both surfaces. The process gives the steel a durable anti-corrosion layer that protects the base metal for decades in many environments, which is why galvanized coil is one of the most widely used steel products in construction, industry and transport. Hot-dip galvanizing accounts for roughly 80 % of all industrial galvanizing because it combines the lowest cost with the best coating adhesion among the common zinc-coating methods.

How the Protection Works

The coating protects the steel in two ways. First, it acts as a barrier that separates the steel from water and oxygen. Second, it provides cathodic protection: zinc is electrochemically more active than iron, so at a scratch or cut edge the zinc corrodes preferentially and the steel remains intact. This sacrificial action is what makes galvanized steel reliable at damaged areas where a painted coating alone would fail. The service life of the steelwork is therefore extended substantially, with lower maintenance than any painting scheme in the same environment.

Main Advantages

Corrosion resistance: effective in atmospheric, rural, industrial and many marine environments

Long service life: decades of protection depending on coating mass and environment

Cathodic protection at cut edges and scratches

Good formability: the zinc layer bends, rolls and stamps without flaking when correctly specified

Paintability: the surface can be painted or further coated for decoration or extra protection

Economy: lowest cost per square metre of protection among common anti-corrosion systems

Resource saving: longer service life means less steel replacement and less energy for maintenance

Production Process

On a continuous galvanizing line, the cold-rolled strip is cleaned in an alkaline bath, annealed in a reducing atmosphere, and immersed in a bath of molten zinc containing small additions of aluminium. Air knives wipe the strip to control the coating thickness, and the strip is then cooled, skin-passed for flatness and surface finish, and given a passivation or oiling treatment to prevent white rust during storage. The coating mass is expressed in g/m2 for the total of both sides, with common classes from Z100 (about 7 µm per side) to Z600 (about 42 µm per side).

Standards and Grades

Hot-dip galvanized sheet and coil are specified according to international standards:

ISO 3575: continuous hot-dip zinc-coated carbon steel sheet of commercial and drawing qualities

EN 10346: European standard for continuously hot-dip coated steel flat products, grades DX51D to DX57D and structural grades S220GD to S550GD

GB/T 2518: Chinese standard for continuously hot-dip zinc-coated steel sheet and strip

ASTM A653: US standard for hot-dip zinc-coated steel sheet

Typical grades cover commercial quality (CQ), deep drawing quality (DDQ) and structural quality with yield strengths up to 550 MPa.

Applications

Roofing and wall cladding of industrial and agricultural buildings

Roll-formed purlins, trusses and structural sections

HVAC ducting, cable trays and electrical enclosures

Automotive body parts and underbody components

White goods housings and general engineering

Tile ridge plates and low-alloy structural profiles

Selection Considerations

Choose the coating mass according to the environment: Z100-Z140 for dry indoor use, Z180-Z275 for normal outdoor buildings, and Z350 or higher for coastal or industrial atmospheres. Choose the grade by the forming operation: deep-drawing grades for severe deformation, structural grades for load-bearing sections. Check the surface treatment (passivated, oiled, or both) to avoid white rust during sea transport, and verify the spangle type if a specific appearance is required.

FAQ

Why does galvanized steel last longer than painted steel?

Because the zinc coating protects the steel even where the coating is damaged. A scratch through a paint film exposes bare steel to corrosion, while a scratch through zinc is protected by the sacrificial action of the surrounding zinc.

What is the difference between electro-galvanized and hot-dip galvanized coil?

Hot-dip coating is thicker and metallurgically bonded, giving much better corrosion resistance, and is the standard for construction and structural use. Electro-galvanizing gives a thinner, smoother coating used mainly for automotive and electronics applications.

Can galvanized coil be welded?

Yes, with appropriate welding parameters and ventilation, because the zinc burns off at welding temperature and releases fumes. The weld area should be touched up with a zinc-rich paint afterwards.

How is coating mass measured?

By weighing a specimen before and after dissolving the zinc layer, per ISO 1460 or the applicable product standard. The result is reported as total coating mass per square metre for both sides.

What causes white rust on new coils and how is it avoided?

White rust forms when wet coils are stored with restricted airflow between wraps. It is prevented by passivation, oiling or chromate-free treatments, and by storing coils dry and well ventilated.

Send Inquiry