100 kVA Single-Phase Oil-Type Pad-Mounted Transformer: Ratings and Design

Oct 29, 2025

Leave a message

Where a 100 kVA Pad-Mounted Unit Is Used

Pad-mounted distribution transformers are installed at grade level on a concrete pad, fed from an underground primary cable and connected to a secondary network that serves a small group of customers. A 100 kVA single-phase rating suits residential blocks, small commercial premises, pumping stations and rural distribution laterals where the load is single-phase and the primary is a radial or loop-fed cable.

Because the unit sits in a public area, the enclosure is a design driver: the high-voltage and low-voltage compartments must be separated, doors must be lockable and the high-voltage terminations must be screened to prevent accidental contact.

Typical Ratings and Taps

Parameter Typical Value
Rated capacity 100 kVA
Primary voltage Dual or single primary, for example 13.8 kV, 13.2 kV, 12.47 kV, 7.2 kV or 34.5 kV class windings
Secondary voltage 120/240 V, three-wire, or 240/480 V
High-voltage taps Two taps of 2.5 % above and below rated voltage, externally operable
Connection Single-phase, two-winding, with additive polarity
Cooling Liquid-immersed, self-cooled (ONAN)
Insulating liquid Mineral insulating oil to IEC 60296, or ester liquid where specified

Split-primary windings are common where two distribution voltages must be available from one unit; the winding is connected in series or parallel at the terminal blocks, and the tap plate must be set correctly before energisation.

Construction Features

The core is normally a wound, rectangular-loop core built from grain-oriented electrical steel, with the coils wound directly onto the core limbs. Copper or aluminium conductors are used depending on the specification. The tank is fabricated from welded steel sheet, grit-blasted and coated with a system suitable for outdoor exposure. Radiator panels or corrugated tank walls provide the cooling surface for self-cooled operation.

Dead-front construction means the high-voltage bushings and cable terminations are behind a locked, removable barrier, with the elbows, inserts and grounding provisions arranged so that the cable can be de-energised and tested without opening the live low-voltage compartment. Loop-feed arrangements allow the primary to continue to the next transformer without a separate junction enclosure.

Standard fittings normally include a pressure relief device, a liquid level indicator, a filler and drain plug, a grounding pad, a nameplate and, where specified, a liquid temperature indicator and a bayonet-type fuse in the high-voltage circuit.

Insulation Level, Temperature Rise and Losses

For a 12 kV class winding (highest voltage for equipment 12 kV), IEC 60076-3 sets a rated lightning impulse withstand level of 75 kV peak and a separate-source power-frequency withstand of 28 kV rms. Insulation levels, dielectric tests and the associated procedures for liquid-immersed transformers are set out in the IEC 60076-3 framework.

Temperature-rise limits for liquid-immersed transformers are given in IEC 60076-2, which sets a top-liquid rise limit of 60 K and an average winding rise limit of 65 K for the standard temperature-rise classes; North American practice uses the 65 °C average winding rise class defined in IEEE C57.12.00. General requirements for liquid-immersed distribution transformers, including ratings, tolerances and construction, are covered in IEEE C57.12.00, and the corresponding test code is IEEE C57.12.90.

Loss tolerances follow IEC 60076-1: total losses may exceed the declared value by no more than 15 %, and short-circuit impedance is subject to a tolerance of plus or minus 10 % of the declared value. Efficiency requirements for units placed on the market in regulated territories should be confirmed against the applicable local efficiency regulation before the design is frozen.

Tests and Verification

Routine tests normally include winding resistance measurement, voltage ratio and polarity, no-load loss and no-load current, load loss and impedance, applied potential and induced potential tests, and insulation resistance. Type and special tests may add temperature rise, lightning impulse, sound level determination according to IEC 60076-10, and short-circuit withstand capability verified against IEC 60076-5 where the purchaser requires it.

On site, the unit should be checked for oil level, pressure-relief condition, tap setting and correct phase identification before the primary is energised.

Frequently Asked Questions

Q: What is the difference between a pad-mounted and a pole-mounted transformer?
A: A pad-mounted unit sits on a concrete pad and is fed by underground cable with a tamper-resistant enclosure, while a pole-mounted unit is installed on an overhead structure and fed from overhead lines.

Q: Can a 100 kVA single-phase unit serve three-phase loads?
A: No. A single-phase transformer supplies single-phase loads; three-phase loads need either a three-phase unit or a bank of single-phase units connected for the required voltage and phase relationship.

Q: Why are taps usually set at plus and minus 2.5 %?
A: They give a practical range for correcting primary voltage variation; the tap is changed off-circuit with the unit de-energised and isolated.

Q: Which insulating liquid is used?
A: Mineral insulating oil meeting IEC 60296 is standard, with natural or synthetic ester liquids specified where fire point or biodegradability requirements demand them.

Q: How is the temperature rise limited?
A: The design limits top-liquid rise to 60 K and average winding rise to 65 K under the conditions defined in IEC 60076-2 for liquid-immersed transformers.

Q: What should be checked before energising?
A: Oil level, absence of leaks, tap position, relief device condition, correct cable connection and phase identification, and a satisfactory insulation resistance and ratio test.

Send Inquiry